Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CAMSHAFT › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351453 CAMSHAFT A

6AR-FSE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of ignition coil assembly

·

Replacement of fuel pump with seal assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT WHEEL RH

Hide 53736 4.REMOVE FRONT FENDER APRON SEAL RH

Hide 53295E 5.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 6.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 8.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 9.DISCONNECT HOSES

a.
A413588

Disengage the 3 clamps.


Hide 10.REMOVE FUEL HOSE BRACKET

a.
A413590

Disengage the 2 clamps to disconnect the 2 fuel hoses.


b.
A413591

Remove the engine cover joint and fuel hose bracket from the EGR valve bracket.


Hide 23021 11.REMOVE FUEL PUMP WITH SEAL SUB-ASSEMBLY (for High Pressure)

Hide 82121 12.DISCONNECT ENGINE WIRE

a.
A413589

Disengage the clamp.


b.

Disconnect the connectors and disengage the clamps.

A413593C01
0,0 0,0 false
V100136

Bolt
V100137

Nut



c.

Remove the bolts and nuts and disconnect the engine wire from the engine.


Hide 29300 13.REMOVE VACUUM PUMP ASSEMBLY

Hide 12262 15.DISCONNECT NO. 2 VENTILATION HOSE

Hide 11201 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 17.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A337565C01
1.156,0.958 1.885,0.385 1.885,0.385 2.927,1.042 true 2.417,3.51 2.219,3.51 2.219,3.51 1.667,3.031 true 2.917,2.24 2.917,1.667 true 1.115,1.146 1.927,2.083 1.927,2.083 2.927,1.219 true 1.813,0.177 2.115,0.385 0.302,0.208 10 true *a 1.885,2.115 2.198,2.271 0.313,0.156 10 true *b 2.458,3.438 2.771,3.594 0.313,0.156 10 true *c 2.875,2.271 3.031,2.469 0.156,0.198 10 false A
*a Paint Mark
*b Timing Mark
*c Timing Notch (Groove)


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.


b.

Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

HINT:

"A" is not a timing mark.



c.

Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.


Hide 11324 18.REMOVE TIMING CHAIN COVER PLATE

a.
A337566

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 13540 19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A337567N01
1.865,0.021 2.115,0.26 0.25,0.24 10 false 15°

Turn the crankshaft pulley approximately 15° clockwise.


b.
A337568N01
1.875,0.031 2.333,0.229 0.458,0.198 10 false 15°

Turn the crankshaft pulley approximately 15° counterclockwise.


c.
A337569C01
1.115,1.708 1.521,1.708 true 0.74,0.323 0.958,0.323 0.958,0.323 1.344,0.781 true 1.552,1.635 1.865,1.792 0.313,0.156 10 true *a 0.521,0.26 0.708,0.458 0.188,0.198 10 true *b
*a Pin
*b Stopper Plate


Align the holes of the stopper plate and No. 1 chain tensioner assembly, and insert a pin into the stopper plate hole to lock the No. 1 chain tensioner assembly.


d.
A337567N01
1.865,0.021 2.115,0.26 0.25,0.24 10 false 15°

Turn the crankshaft pulley approximately 15° clockwise.


e.
A337570

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.

NOTICE:

Make sure not to drop the gasket inside the timing chain cover sub-assembly.



f.
A337568N01
1.875,0.031 2.333,0.229 0.458,0.198 10 false 15°

Turn the crankshaft pulley approximately 15° counterclockwise.


Hide 15370 21.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13523F 22.REMOVE CAMSHAFT TIMING GEAR BOLT

a.
A413594C01
1.948,0.177 2.26,0.375 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Hold the hexagonal portion of the camshaft with a wrench and remove the camshaft timing gear bolt from the camshaft.

NOTICE:

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.



Hide 23.REMOVE CAMSHAFT BEARING CAP

a.
A337573N01
0.323,1.583 0.479,1.781 0.156,0.198 10 true 1 0.333,1.26 0.49,1.458 0.156,0.198 10 true 3 0.375,0.427 0.531,0.625 0.156,0.198 10 true 2 1.042,1.615 1.198,1.813 0.156,0.198 10 true 7 1.25,0.271 1.406,0.469 0.156,0.198 10 true 6 1.958,1.615 2.146,1.844 0.188,0.229 10 true 11 1.729,0.292 1.938,0.458 0.208,0.167 10 true 10 2.063,0.354 2.271,0.521 0.208,0.167 10 true 8 3.146,0.688 3.354,0.854 0.208,0.167 10 true 4 3.167,1.302 3.375,1.469 0.208,0.167 10 true 5 2.573,1.156 2.781,1.323 0.208,0.167 10 true 9

Remove the 11 bolts in several steps in the order shown in the illustration.


b.
A337575C02
0.792,0.677 0.792,0.198 0.792,0.198 0.906,0.198 true 1.292,0.719 1.292,0.198 1.292,0.198 1.406,0.198 true 1.802,0.677 1.802,0.198 1.802,0.198 1.917,0.198 true 2.354,0.667 2.354,0.188 2.354,0.188 2.469,0.188 true 0.302,1.656 0.458,1.854 0.156,0.198 10 true 1 0.302,0.948 0.458,1.146 0.156,0.198 10 true 2 1.271,1.927 1.427,2.125 0.156,0.198 10 true 5 1.01,0.656 1.167,0.854 0.156,0.198 10 true 6 1.781,1.917 1.938,2.115 0.156,0.198 10 true 9 2.292,1.917 2.448,2.115 0.156,0.198 10 true 7 1.448,0.656 1.688,0.844 0.24,0.188 10 true 10 2.031,0.667 2.188,0.865 0.156,0.198 10 true 8 3.156,1.021 3.313,1.219 0.156,0.198 10 true 4 2.802,1.906 2.958,2.104 0.156,0.198 10 true 3 0.938,0.125 1.167,0.313 0.229,0.188 10 true *1 1.438,0.125 1.719,0.292 0.281,0.167 10 true *2 1.948,0.125 2.198,0.333 0.25,0.208 10 true *3 2.5,0.125 2.74,0.333 0.24,0.208 10 true *4
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Remove the 10 bolts in several steps in the order shown in the illustration.


c.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 24.REMOVE CAMSHAFT

a.
A337577

Raise the camshaft as shown in the illustration to remove it from the camshaft timing gear assembly.

NOTICE:

Be careful not to damage the camshaft or camshaft timing gear assembly with the wrench.



Hide 13050 25.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A337578

Remove the camshaft timing gear assembly.

NOTICE:
·

Do not disassemble the camshaft timing gear assembly.

·

Be careful not to damage the camshaft timing gear assembly.




Hide 13512 26.REMOVE NO. 2 CAMSHAFT

a.
A337579

Hold up the chain sub-assembly and remove the No. 2 camshaft from the camshaft housing sub-assembly.


b.
A337580

Suspend the chain sub-assembly with a string or equivalent as shown in the illustration.

NOTICE:

Be careful not to drop the chain sub-assembly inside the timing chain cover sub-assembly.



Hide 13070A 27.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A350374C03
0.75,0.781 0.875,0.781 0.875,0.781 0.875,1.26 true 2.667,0.958 2.521,1.271 2.521,1.271 2.365,1.271 true 0.469,0.708 0.927,0.906 0.458,0.198 10 false SST 2.188,1.177 2.5,1.375 0.313,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure the SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A337581

Remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:

Do not disassemble the camshaft timing exhaust gear assembly.



Hide 15678A 28.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 29.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 30.REMOVE NO. 2 CAMSHAFT BEARING