Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P001700  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate exhaust valve open and close timing is controlled by the ECM. The ECM performs exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing exhaust gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviation in the crank position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored SAE Code:
P0017

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crank position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A416572E03
4.031,0.427 4.198,0.427 4.198,0.427 4.333,1.115 false 0.188,0.49 2.177,0.688 1.99,0.198 10 false Vehicle Speed 0.76,1.771 2.75,1.969 1.99,0.198 10 false Idling 0.208,2.031 1.125,2.573 0.917,0.542 10 false Engine Switch on (IG) 1.531,2.146 1.833,2.448 0.302,0.302 10 false [A] 2.198,1.667 2.5,1.969 0.302,0.302 10 false [B] 3.188,1.656 3.49,1.958 0.302,0.302 10 false [C] 3.823,3.01 4.125,3.313 0.302,0.302 10 false [D] 4.469,0.885 4.771,1.188 0.302,0.302 10 false [E] 5.75,1.667 6.052,1.969 0.302,0.302 10 false [F] 6.365,3.021 6.667,3.323 0.302,0.302 10 false [G] 1.917,2.625 2.698,3.146 0.781,0.521 10 false Warming up the engine 2.74,2.625 3.969,2.875 1.229,0.25 10 false 5 minutes or more 4.104,2.635 5.031,2.917 0.927,0.281 10 false 2 to 3 minutes 5.24,2.635 6.396,2.875 1.156,0.24 10 false 5 minutes or more 1.74,0.333 4.042,0.594 2.302,0.26 10 false There is no designated vehicle speed 6.698,2.448 7.073,2.688 0.375,0.24 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Idle the engine for 5 minutes or more [C].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P001700.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [E] through [G].



15.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Idle the engine for 5 minutes or more [F].

17.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by one tooth or more.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001700)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001700 is output A
DTC P001700 and other DTCs are output B


HINT:

If any DTCs other than P001700 is output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1 / Data List / Exhaust VVT Change Angle Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
50004 372 5 398

e.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

5.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Inspect the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
A412762C01
1.042,0.74 1.354,0.74 true 1.417,0.667 1.729,0.823 0.313,0.156 10 false *1
*1 Oil Control Valve Filter


a.

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001700 is output B




A

B