Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P013613  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open  P013617  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold  P01361C  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P003612.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P003612

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P013613 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open Abnormal voltage output:
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage does not increase to 0.69 V or higher.

(b) Heated oxygen sensor voltage does not decrease to less than 0.21 V.


·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel system

·

PCV valve and hose

·

Intake system

·

EGR valve assembly


Comes on DTC stored SAE Code:
P0136
P013617 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is less than 0.21 V.

(b) Target air fuel ratio is rich.


·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system

·

EGR valve assembly


Comes on DTC stored SAE Code:
P0137
P01361C O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Out of Range High voltage (short):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is higher than 0.69 V.

(b) Target air fuel ratio is lean.


·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code:
P0138

MONITOR DESCRIPTION

Active Air Fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P013613)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to less than 0.21 V and does not increase to 0.69 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P013613.

A152942E91
2.969,2.115 3.115,1.792 3.115,1.792 3.292,1.792 false 2.792,2.333 2.906,2.625 2.906,2.625 3.073,2.625 false 0.073,0.083 5.531,0.323 5.458,0.24 10 false Heated Oxygen Sensor Circuit Malfunction (P013613: Abnormal Voltage) 4.729,1.302 5.427,1.479 0.698,0.177 10 false Operation 4.229,0.792 5.885,0.948 1.656,0.156 10 false Approximately 30 seconds 3.333,1.708 3.854,1.896 0.521,0.188 10 false Normal 2.177,1.354 2.635,1.656 0.458,0.302 10 false OFF 2.083,2.125 2.563,2.417 0.479,0.292 10 false 0.69 V 2.083,2.896 2.667,3.135 0.583,0.24 10 false 0.21 V 3.125,2.542 3.813,2.729 0.688,0.188 10 false Abnormal 0.052,1.333 2.125,1.729 2.073,0.396 10 false Active Air Fuel Ratio Control 0.052,2.531 2.646,2.865 2.594,0.333 10 false Heated Oxygen Sensor Voltage


Open or Short in Heated Oxygen Sensor Circuit (DTC P013617 or P01361C)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P013617. When the target air fuel ratio is lean and the voltage output is higher than 0.69 V (rich) during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P01361C.

*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P042000

A152992E67
5.813,3.802 6.021,4.063 false 4.281,2.042 4.448,1.729 false 4.448,1.729 4.594,1.729 false 5.344,2.406 5.448,1.719 false 5.448,1.719 5.625,1.719 false 5.677,3.01 5.844,2.563 false 5.844,2.563 6,2.563 false 5.74,6.573 5.969,6.104 false 5.969,6.104 6.104,6.104 false 0.063,0.052 4.271,0.313 4.208,0.26 10 false Heated Oxygen Sensor Circuit Low Voltage (P013617: Open) 0.281,1.219 1.177,1.688 0.896,0.469 10 false Active Air Fuel Ratio Control 0.281,3.208 1.24,3.708 0.958,0.5 10 false Heated Oxygen Sensor Voltage 0.281,2.083 1.688,2.375 1.406,0.292 10 false Target Air Fuel Ratio 1.979,2.031 2.938,2.396 0.958,0.365 10 false Stoichiometric Air Fuel Level 2.781,1.313 3.146,1.51 0.365,0.198 10 false OFF 2.49,3.479 2.979,3.677 0.49,0.198 10 false 0.21 V 0.063,4.208 4.75,4.417 4.688,0.208 10 false Heated Oxygen Sensor Circuit High Voltage (P01361C: Short) 0.281,4.854 1.198,5.271 0.917,0.417 10 false Active Air Fuel Ratio Control 0.281,6.906 1.25,7.354 0.969,0.448 10 false Heated Oxygen Sensor Voltage 0.281,5.74 1.677,6.031 1.396,0.292 10 false Target Air Fuel Ratio 2.094,5.667 3.042,6.031 0.948,0.365 10 false Stoichiometric Air Fuel Level 2.698,4.938 3.052,5.135 0.354,0.198 10 false OFF 3.99,0.313 5.646,0.51 1.656,0.198 10 false Approximately 30 seconds 4.521,1.323 5.281,1.521 0.76,0.198 10 false Operation 4.479,4.958 5.177,5.156 0.698,0.198 10 false Operation 4.656,5.75 5.052,5.948 0.396,0.198 10 false Lean 4.656,1.646 5.219,1.844 0.563,0.198 10 false Normal 6.146,6.01 6.833,6.208 0.688,0.198 10 false Abnormal 5.688,1.625 6.333,1.823 0.646,0.198 10 false Abnormal 6.063,4.063 6.802,4.26 0.74,0.198 10 false Abnormal 6.052,2.479 6.615,2.677 0.563,0.198 10 false Normal 4.781,2.458 5.146,2.656 0.365,0.198 10 false Rich 2.5,6.677 2.99,6.875 0.49,0.198 10 false 0.69 V


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Crank position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active air fuel ratio control Executing
Active air fuel ratio control begins when all of following conditions met: -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 90%

TYPICAL MALFUNCTION THRESHOLDS

P013613: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
Either of following conditions is met 1 or 2
1. Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V
2. Both of following conditions are met -
(c) Commanded air fuel ratio 14.8 or more
(d) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V

P013617: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage Less than 0.21 V

P01361C: Heated Oxygen Sensor Voltage Check (High Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.8 or more
(b) Heated oxygen sensor voltage Higher than 0.69 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E71
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.958 0.229,0.24 10 false [C] 3.49,2.906 4.792,3.083 1.302,0.177 10 false 10 minutes or more 1.094,1.354 1.719,1.635 0.625,0.281 10 false 75 km/h 2.021,2.427 2.25,2.625 0.229,0.198 10 false [A] 1.021,0.479 1.677,0.688 0.656,0.208 10 false 120 km/h 1.25,2.229 1.635,2.448 0.385,0.219 10 false Idling 0.479,2.698 1.406,3.281 0.927,0.583 10 false Engine Switch on (IG) 2.677,2.135 2.906,2.344 0.229,0.208 10 false [B] 2.333,2.917 3.156,3.115 0.823,0.198 10 false Warming up 5.01,3.313 5.271,3.573 0.26,0.26 10 false [D] 0.75,0.146 1.813,0.385 1.063,0.24 10 false Vehicle Speed 5.813,2.708 6.344,2.99 0.531,0.281 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Drive the vehicle at 75 to 120 km/h (46 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P013613, P013617 or P01361C.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [C] through [D] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Active Test "Control the Injection Volume for A/F Sensor". This Active Test can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following procedure describes how to perform the Active Test "Control the Injection Volume for A/F Sensor" using the GTS.


1.

Connect the GTS to the DLC3.

2.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

3.

Turn the GTS on.

4.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

5.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

6.

Perform the Active Test with the engine idling (change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.


HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

Each sensor reacts in accordance with increase and decreases in the fuel injection volume.



Standard
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E20
5.792,3.625 7.115,3.896 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 false 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 false 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.792,0.583 2.802,0.969 2.01,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.604 6.969,5.979 1.052,0.375 10 false - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 false - Heated oxygen sensor heater 5.927,6.792 6.969,7.229 1.042,0.438 10 false - Heated oxygen sensor circuit 5.927,7.469 6.813,7.875 0.885,0.406 10 false - Fuel injector assembly 5.917,8.083 7.073,8.417 1.156,0.333 10 false - Fuel pressure 5.917,8.531 7.01,9.313 1.094,0.781 10 false - Gas leak from exhaust system 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Performing the Active Test "Control the Injection Volume for A/F Sensor" allows the output voltage of the air fuel ratio sensor and heated oxygen sensor to be checked and graphed.

·

To display the graph, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; and then press the graph button on the Data List view.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P013613, P013617 OR P01361C)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P01361C is output A
DTC P013617 is output B
DTC P013613 is output C
DTC P013613, P013617 or P01361C and other DTCs are output D


HINT:

If any DTCs other than P013613, P013617 and P01361C are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2)

B

14.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and O2 Sensor Voltage B1S2.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
O2 Sensor Voltage B1S2
50003 372 205,218

f.

Read the heated oxygen sensor output voltage while idling.

Result:
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B




A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A292987C05
0.792,2.208 1.354,1.927 false 0.813,1.094 1.365,1.479 false 2.052,1.958 2.344,2.229 false 0.219,0.188 0.531,0.385 0.313,0.198 10 *a 0.563,0.948 0.875,1.146 0.313,0.198 10 +B 0.531,2.167 0.844,2.365 0.313,0.198 10 E2 2.271,2.323 2.74,2.531 0.469,0.208 10 OX1B
*a Component without harness connected
(Heated Oxygen Sensor)


a.

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 3 (OX1B) Always 10 kΩ or higher
2 (+B) - 4 (E2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the engine switch off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-17 (HT1B) - C58-99 (OX1B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM)

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / Coolant Temperature, A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 205,225,218

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as A/F (O2) Sensor Voltage B1S1, and the heated oxygen sensor is displayed as O2 Sensor Voltage B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS Display (Sensor) Voltage Variation Proceed to
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
Alternates between higher than and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2 Sensor Voltage B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (A/F (O2) Sensor Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A337301E01
4.479,1.479 4.813,1.313 4.813,1.313 4.979,1.313 false 4.5,2.302 4.667,2.635 4.667,2.635 4.833,2.635 false 3.5,1.708 3.563,1.854 3.563,1.854 3.729,1.854 false 0.375,2.479 1.448,2.677 1.073,0.198 10 false Voltage 5.854,0.708 6.979,0.958 1.125,0.25 10 false Injection Volume 2.188,0.333 3.313,0.583 1.125,0.25 10 false 12.5% 3.51,1.167 4.635,1.417 1.125,0.25 10 false -12.5% 3.76,1.781 4.25,2.135 0.49,0.354 10 true Normal 5.052,1.24 6.177,1.49 1.125,0.25 10 false Malfunction 0.938,1.885 2.063,2.135 1.125,0.25 10 false 3.3 V 1.052,2.896 2.177,3.146 1.125,0.25 10 false 1 V 1.052,3.396 2.177,3.646 1.125,0.25 10 false 0 V 5.667,2.927 7.104,3.365 1.438,0.438 10 false Heated Oxygen Sensor Output 5.74,1.708 7.063,2.135 1.323,0.427 10 false Air Fuel Ratio Sensor Output 4.906,2.552 6.031,2.802 1.125,0.25 10 false Malfunction



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 2.2 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and A/F (O2) Sensor Current B1S1.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
A/F (O2) Sensor Current B1S1
50003 372 205,230

i.

Drive the vehicle at 60 km/h (37 mph) or more and release the accelerator pedal for at least 5 seconds without depressing the brake pedal in order to execute fuel-cut control. Perform this 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A416606E01
0.188,0.125 3.125,0.365 2.938,0.24 12 false Driving Pattern: 0.146,0.844 3.083,1.083 2.938,0.24 10 false Vehicle Speed 0.5,1.438 3.438,1.677 2.938,0.24 10 false 60 km/h 0.573,2.188 3.51,2.427 2.938,0.24 10 false 0 km/h 1.313,2.531 2.573,2.771 1.26,0.24 10 false 10 minutes or more 3.063,2.542 4.323,2.781 1.26,0.24 10 false 5 minutes or more 4.302,2.542 5.563,2.781 1.26,0.24 10 false 5 minutes or more 5.521,2.542 6.781,2.781 1.26,0.24 10 false 5 minutes or more 6.417,2.344 6.906,2.594 0.49,0.25 10 false Time


j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is performed.

Standard Current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result:
Proceed to
OK
NG



OK

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / Coolant Temperature and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
O2 Sensor Voltage B1S2
50004 372 8 205,218

f.

Change the fuel injection volume using the GTS and monitor the voltage output of the heated oxygen sensor displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less, and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

14.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / Coolant Temperature, A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 205,225,218

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as A/F (O2) Sensor Voltage B1S1, and the heated oxygen sensor is displayed as O2 Sensor Voltage B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS Display (Sensor) Voltage Variation Proceed to
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
Alternates between higher than and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2 Sensor Voltage B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (A/F (O2) Sensor Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A337301E01
4.479,1.479 4.813,1.313 4.813,1.313 4.979,1.313 false 4.5,2.302 4.667,2.635 4.667,2.635 4.833,2.635 false 3.5,1.708 3.563,1.854 3.563,1.854 3.729,1.854 false 0.375,2.479 1.448,2.677 1.073,0.198 10 false Voltage 5.854,0.708 6.979,0.958 1.125,0.25 10 false Injection Volume 2.188,0.333 3.313,0.583 1.125,0.25 10 false 12.5% 3.51,1.167 4.635,1.417 1.125,0.25 10 false -12.5% 3.76,1.781 4.25,2.135 0.49,0.354 10 true Normal 5.052,1.24 6.177,1.49 1.125,0.25 10 false Malfunction 0.938,1.885 2.063,2.135 1.125,0.25 10 false 3.3 V 1.052,2.896 2.177,3.146 1.125,0.25 10 false 1 V 1.052,3.396 2.177,3.646 1.125,0.25 10 false 0 V 5.667,2.927 7.104,3.365 1.438,0.438 10 false Heated Oxygen Sensor Output 5.74,1.708 7.063,2.135 1.323,0.427 10 false Air Fuel Ratio Sensor Output 4.906,2.552 6.031,2.802 1.125,0.25 10 false Malfunction



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50004 372 25 211,385,205

f.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Result:
Proceed to
OK
NG



OK

11.REPLACE AIR FUEL RATIO SENSOR

NG

10.INSPECT EGR VALVE ASSEMBLY
10.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

11.REPLACE AIR FUEL RATIO SENSOR

NG

11.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613 OR P01361C)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613 OR P01361C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013613 or P01361C.


d.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013613 or P01361C is output)
B




A

END

B

14.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

16.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C95-1 (HT1B) - C58-17 (HT1B) Always Below 1 Ω
C95-3 (OX1B) - C58-99 (OX1B) Always Below 1 Ω
C95-4 (E2) - C58-100 (EX1B) Always Below 1 Ω
C95-1 (HT1B) or C58-17 (HT1B) - Body ground and other terminals Always 10 kΩ or higher
C95-3 (OX1B) or C58-99 (OX1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50004 372 25 211,385,205

f.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Result:
Proceed to
OK
NG



OK

19.REPLACE HEATED OXYGEN SENSOR

NG

18.INSPECT EGR VALVE ASSEMBLY
18.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

19.REPLACE HEATED OXYGEN SENSOR

NG

19.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

20.CLEAR DTC
20.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613, P013617 OR P01361C)
21.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613, P013617 OR P01361C)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P013613, P013617 or P01361C.


d.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013613, P013617 or P01361C is output)
B



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

END

B