Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P03351F  Crankshaft Position Sensor "A" Circuit Intermittent  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

Refer to DTC P033511.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P033511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03351F Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crank position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or higher.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crank position sensor circuit

·

Crank position sensor

·

Crankshaft (crankshaft position sensor plate)

·

ECM


Does not come on DTC stored SAE Code: P0339
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range No crank position sensor signal to the ECM while cranking (1 trip detection logic).
·

Open or short in crank position sensor circuit

·

Crank position sensor

·

Crankshaft (crankshaft position sensor plate)

·

ECM


Comes on DTC stored SAE Code: P0335
P033531 Crankshaft Position Sensor "A" No Signal The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic).
·

Open or short in crank position sensor circuit

·

Crank position sensor

·

Crankshaft (crankshaft position sensor plate)

·

ECM


Comes on DTC stored SAE Code: P0335

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P033511


MONITOR DESCRIPTION

A DTC will be stored if any of the following occurs:

·

The crank position sensor signal (NE signal) is not received by the ECM when the engine is being cranked.

·

The crank position sensor signal (NE signal) is not received by the ECM when the engine is running.

·

The engine stalls and the engine speed signal value decreases rapidly (under normal conditions the engine speed will decrease gradually).


MONITOR STRATEGY

Required Sensors/Components (Main) Crank position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Run the engine at an engine speed of 1000 rpm for 5 seconds or more.

9.

Turn the GTS on.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P03351F, P03352A or P033531.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

(e)

Start the engine.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crank position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crank position sensor output voltage is insufficient.


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK A
Does not crank at all* B


HINT:

*: When the engine cannot crank, there may be a malfunction in the starter assembly.




A

2.READ VALUE USING GTS (ENGINE SPEED)

B

GO TO PROBLEM SYMPTOMS TABLE (ENGINE DOES NOT CRANK (DOES NOT START))

2.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crank position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
A424806C01
0.177,1 0.594,1.24 0.417,0.24 0.917,1.917 1.438,1.167 true 2.5,1.917 1.917,1.167 true 1.667,1.917 1.667,1.167 true 0.219,1.031 0.833,1.229 0.615,0.198 10 false C104 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.771,1.917 1.083,2.115 0.313,0.198 10 false VC 1.563,1.927 2.021,2.125 0.458,0.198 10 false NE- 2.458,1.927 2.917,2.125 0.458,0.198 10 false NE+
*a Front view of wire harness connector
(to Crank Position Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the crank position sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C104-1 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C104-3 (NE+) - Body ground Engine switch on (IG) 3.0 to 5.0 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C104-1 (VC) - C104-3 (NE+) Engine switch off 1.425 to 1.575 kΩ
C104-2 (NE-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CRANK POSITION SENSOR)

NG

6.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
4.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (CRANK POSITION SENSOR)
B319222C07
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


a.

Visually check the crank position sensor for damage.


b.

Check the crank position sensor installation condition.

OK:

The crank position sensor does not have any damage and is installed properly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)

NG

5.INSPECT CRANKSHAFT (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)
a.

Inspect the teeth of the crankshaft position sensor plate.

OK:

Crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
a.

Disconnect the crank position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C104-1 (VC) - C58-110 (VCNE) Always Below 1 Ω
C104-3 (NE+) - C58-76 (NE+) Always Below 1 Ω
C104-2 (NE-) - C58-109 (NE-) Always Below 1 Ω
C104-1 (VC) or C58-110 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
C104-3 (NE+) or C58-76 (NE+) - Body ground and other terminals Always 10 kΩ or higher
C104-2 (NE-) or C58-109 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR