Refer to DTC P036511.
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P036511
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P03652A | Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range | No camshaft position sensor (for exhaust camshaft) signal to ECM while engine cranking (1 trip detection logic). | ·
Open or short in camshaft position sensor (for exhaust camshaft) circuit ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0365 |
| P036531 | Camshaft Position Sensor "B" Bank 1 No Signal | No camshaft position sensor (for exhaust camshaft) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). | ·
Open or short in camshaft position sensor (for exhaust camshaft) circuit ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
ECM |
Comes on | DTC stored | SAE Code: P0365 |
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P034011
If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Camshaft position sensor (for exhaust camshaft) |
| Required Sensors/Components (Related) | Crank position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Idle the engine for 10 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P03652A or P036531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P036511.
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P036511
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft)) |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| C20-1 (VVE+) - Body ground | Engine switch on (IG) | 3.0 to 5.0 V |
Turn the engine switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-3 (VC2) - C20-1 (VVE+) | Engine switch off | 1.425 to 1.575 kΩ |
| C20-2 (VVE-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Clearance |
Visually check the camshaft position sensor (for exhaust camshaft) for damage.
Check the camshaft position sensor (for exhaust camshaft) installation condition.
The camshaft position sensor (for exhaust camshaft) does not have any damage and is installed properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the exhaust camshaft.
Camshaft timing rotor does not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the exhaust camshaft.
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C20-3 (VC2) - C58-111 (VCE1) | Always | Below 1 Ω |
| C20-1 (VVE+) - C58-81 (EV1+) | Always | Below 1 Ω |
| C20-2 (VVE-) - C58-112 (EV1-) | Always | Below 1 Ω |
| C20-3 (VC2) or C58-111 (VCE1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C20-1 (VVE+) or C58-81 (EV1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C20-2 (VVE-) or C58-112 (EV1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG