The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU adjust the fuel pump operation speed.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Check whether operating sounds can be heard while operating the fuel pump using the GTS.
Operating sounds can be heard from the fuel pump.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Fuel Pump [for Low Pressure Side]) |
Remove the fuel pump (for low pressure side) from the fuel tank assembly.
Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL PUMP>REMOVAL
Clean the fuel pump to completely remove any remaining fuel.
Connect the fuel pump connector.
Make sure that there is no fuel remaining inside or on the outside of the fuel pump.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.
| Tester Display |
|---|
| Control the Fuel Pump Duty Ratio |
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | GTS Operation | Specified Condition |
|---|---|---|
| 1 - 2 | Fuel pump duty ratio: 25% | 3.2 to 4.05 V |
| Fuel pump duty ratio: 80% | 8.8 to 12.5 V |
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | GTS Operation | Specified Condition |
|---|---|---|
| 1 - 2 | ON (Fuel pump duty ratio: 90%) | 9.0 to 14.0 V |
Be sure to measure the voltage with all the connectors connected.
Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL PUMP>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel pump operation.
Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Malfunction has been repaired successfully.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Pump Control ECU Assembly) |
Disconnect the fuel pump control ECU assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R121-1 (+B) - R121-4 (E) | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump (for low pressure side) connector.
Disconnect the fuel pump control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R44-4 (B) - R121-5 (FP) | Always | Below 1 Ω |
| R44-5 (E) - R121-6 (FP-) | Always | Below 1 Ω |
| R44-4 (B) or R121-5 (FP) - Body ground and other terminals | Always | 10 kΩ or higher |
| R44-5 (E) or R121-6 (FP-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump control ECU assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R121-2 (FPC) - A78-21 (FPC) | Always | Below 1 Ω |
| R121-2 (FPC) or A78-21 (FPC) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Pump Control ECU Assembly) |
Disconnect the fuel pump control ECU assembly connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.
| Tester Display |
|---|
| Activate the Circuit Relay |
Operate the fuel pump control ECU assembly using the Active Test function and measure the resistance according to the value(s) in the table below.
| Tester Connection | Techstream Operation | Specified Condition |
|---|---|---|
| R121-2 (FPC) - Body ground | Before Active Test → During Active Test | Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates* |
*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R121-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 2 relay.
Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | EFI-MAIN NO. 2 Relay |
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (EFI-MAIN NO. 2 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI-MAIN NO. 2 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 1, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays from the engine room relay block and junction block assembly.
Remove the EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 1 relay) - 2 (EFI-MAIN NO. 2 relay) | Always | Below 1 Ω |
| 5 (EFI-MAIN NO. 1 relay) or 2 (EFI-MAIN NO. 2 relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Disconnect the fuel pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (EFI-MAIN NO. 2 relay) - R121-1 (+B) | Always | Below 1 Ω |
| 5 (EFI-MAIN NO. 2 relay) or R121-1 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG