In this circuit, the compressor assembly with pulley (compressor solenoid)*1 or cooler compressor assembly (compressor solenoid)*2 receives refrigerant compression demand signals from the air conditioning amplifier assembly.
Based on this signal, the compressor assembly with pulley (compressor solenoid)*1 or cooler compressor assembly (compressor solenoid)*2 changes the amount of compressor output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1451 | Compressor Solenoid Circuit | Open or short in compressor solenoid circuit | ·
Compressor assembly with pulley (compressor solenoid)*1 ·
Cooler compressor assembly (compressor solenoid)*2 ·
Harness or connector ·
Air conditioning amplifier assembly |
- |
*1: for 2AR-FE, A25A-FKS
*2: for 6AR-FSE, 2GR-FKS
for 2AR-FE, A25A-FKS
for 6AR-FSE, 2GR-FKS
| Result | Proceed to |
|---|---|
| for 2AR-FE, A25A-FKS | A |
| for 6AR-FSE, 2GR-FKS | B |
A
B
| *a | Front view of wire harness connector
(to Compressor Assembly with Pulley (Compressor Solenoid)) |
Disconnect the C98 compressor assembly with pulley (compressor solenoid) connector.
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. | C98-2 (SOL+) - Body ground |
| Tool Setting | 5 V/DIV., 500 μs./DIV. |
| Condition | ·
Engine running ·
Blower switch: LO ·
A/C switch: On |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AR-FE: Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 2AR-FE)>REMOVAL
for A25A-FKS: Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for A25A-FKS)>REMOVAL
NG
Disconnect the K54 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-2 (SOL+) - K54-3 (SOL+) | Always | Below 1 Ω |
| C98-2 (SOL+) or K54-3 (SOL+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Cooler Compressor Assembly (Compressor Solenoid)) |
Disconnect the C62 cooler compressor assembly (compressor solenoid) connector.
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. | C62-2 (SOL+) - Body ground |
| Tool Setting | 5 V/DIV., 500 μs./DIV. |
| Condition | ·
Engine running ·
Blower switch: LO ·
A/C switch: On |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
for 6AR-FSE: Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 6AR-FSE)>REMOVAL
for 2GR-FKS: Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 2GR-FKS)>REMOVAL
NG
Disconnect the K54 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C62-2 (SOL+) - K54-3 (SOL+) | Always | Below 1 Ω |
| C62-2 (SOL+) or K54-3 (SOL+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG