Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2018.04–2021.02
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0319585 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

for Type A:

i.

Install the 7 hole plugs to the front frame assembly.

HINT:

There are 2 different shapes of hole plug.


C373268N01
2.125,0.375 2.281,0.573 0.156,0.198 10 false A 2.26,0.75 2.417,0.948 0.156,0.198 10 false B 2.615,0.458 2.771,0.656 0.156,0.198 10 false A 2.021,0.615 2.177,0.813 0.156,0.198 10 false A 3.219,1.448 3.375,1.646 0.156,0.198 10 false A 3.792,1.542 3.948,1.74 0.156,0.198 10 false A 4.167,1.573 4.323,1.771 0.156,0.198 10 false A



b.

for Type B:

i.

Install the 9 hole plugs to the front frame assembly.

HINT:

There are 3 different shapes of hole plug.


C425892N01
2.125,0.375 2.281,0.573 0.156,0.198 10 false A 2.26,0.75 2.417,0.948 0.156,0.198 10 false B 2.615,0.458 2.771,0.656 0.156,0.198 10 false A 2.021,0.615 2.177,0.813 0.156,0.198 10 false A 3.198,1.479 3.354,1.677 0.156,0.198 10 false A 3.792,1.542 3.948,1.74 0.156,0.198 10 false A 4.167,1.573 4.323,1.771 0.156,0.198 10 false A 3,1.25 3.146,1.417 0.146,0.167 10 true C 3.313,1.292 3.458,1.458 0.146,0.167 10 true C



Hide 52217E 2.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C373269C01
0.073,0.083 0.385,0.24 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle


Align a new front suspension member body mounting rear cushion LH as shown in the illustration and set it to the front frame assembly.

NOTICE:
·

Position the front suspension member body mounting rear cushion LH in the correct direction.

·

Do not apply lubricant to the outer sleeve of the front suspension member body mounting rear cushion LH.




b.
C374277C01
1.896,0.531 2.792,0.531 false 2.031,0.948 2.458,0.948 2.458,0.948 2.458,0.531 false 2.313,2.656 2.833,2.656 false 1.865,3.063 2.604,3.063 2.604,3.063 2.604,2.656 false 0.719,1.479 0.823,1.479 0.823,1.479 1.396,1.969 false 0.573,1.396 0.885,1.552 0.313,0.156 10 false *1 2.833,0.448 3.292,0.646 0.458,0.198 10 false SST 2.875,2.573 3.333,2.771 0.458,0.198 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09570-24011  
09830-10010  (09830-01010, 09830-01020, 09830-01040, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



c.
C374278C01
1.896,0.823 2.667,1.146 2.667,1.146 2.781,1.146 false 1.417,1.521 2.125,1.521 true 0.344,1.552 0.448,1.552 0.448,1.552 0.823,2.25 true 2.813,1.063 3.125,1.219 0.313,0.156 10 false *a 2.167,1.438 2.625,1.635 0.458,0.198 10 false SST 0.052,1.469 0.51,1.667 0.458,0.198 10 false SST
*a Hold
V113147

Turn


Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion LH.



Hide 52215 3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION

a.
C373272C01
0.063,0.063 0.375,0.219 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle


Align a new front suspension member body mounting rear cushion as shown in the illustration and set it to the front frame assembly.

NOTICE:
·

Position the front suspension member body mounting rear cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the front suspension member body mounting rear cushion.




b.

Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.

SST
09570-24011  
09830-10010  (09830-01010, 09830-01020, 09830-01040, 09830-01060)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



c.

Using SST, install the front suspension member body mounting rear cushion.

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion.


HINT:

Perform the same procedure as for the front suspension member body mounting rear cushion LH.



Hide 52211J 4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for LH Side)

a.
C373273C01
0.083,0.073 0.396,0.229 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle


Align a new front suspension member body mounting front cushion as shown in the illustration and set it to the front frame assembly.

NOTICE:
·

Position the front suspension member body mounting front cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the front suspension member body mounting front cushion.




b.
C373274C01
0.854,1.771 0.958,1.771 0.958,1.771 1.375,2.073 false 2.021,0.979 2.292,0.979 2.292,0.979 2.292,0.563 false 2.24,2.885 2.833,2.885 false 1.854,3.167 2.563,3.167 2.563,3.167 2.563,2.885 false 1.896,0.563 2.688,0.563 false 0.708,1.688 1.021,1.844 0.313,0.156 10 false *1 2.729,0.479 3.188,0.677 0.458,0.198 10 false SST 2.875,2.802 3.333,3 0.458,0.198 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:
·

Be sure to install SST (09830-01030) in the correct direction.

·

Apply molybdenum grease to the threads and tip of the SST center bolt before use.




c.
C373275C01
2.052,0.802 2.188,0.323 2.188,0.323 2.26,0.323 false 0.469,1.156 0.583,1.156 0.583,1.156 1.146,1.604 false 1.792,2.531 2.146,2.531 2.146,2.531 2.146,2.938 false 2.302,0.25 2.615,0.406 0.313,0.156 10 false *a 0.177,1.073 0.635,1.271 0.458,0.198 10 false SST 2.01,2.969 2.469,3.167 0.458,0.198 10 false SST
*a Hold
V113147

Turn


Using SST, install the front suspension member body mounting front cushion as shown in the illustration.

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.



Hide 52211J 5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for RH Side)

a.
C373277C01
0.073,0.073 0.385,0.229 0.313,0.156 10 false *a
*a View from Underneath
V100135

Front of the Vehicle


Align a new front suspension member body mounting front cushion as shown in the illustration and set it to the front frame assembly.

NOTICE:
·

Position the front suspension member body mounting front cushion in the correct direction.

·

Do not apply lubricant to the outer sleeve of the front suspension member body mounting front cushion.




b.

Install SST using the same procedure as for the LH side.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:
·

Be sure to install SST (09830-01030) in the correct direction.

·

Apply molybdenum grease to the threads and tip of the SST center bolt before use.




c.

Using SST, install the front suspension member body mounting front cushion.

NOTICE:

Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.


HINT:

Perform the same procedure as for the LH side.



Hide 52216B 6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.


Hide 52213A 7.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Install the 2 front suspension member body mounting front stoppers to the front frame assembly.


Hide 51227B 8.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for A25A-FKS, 2GR-FKS)

a.

Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 9.INSTALL BOLT (for 2AR-FE, 6AR-FSE)

a.

Install the 2 bolts to the front frame assembly.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 17572B 10.INSTALL NO. 2 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 2 exhaust pipe support bracket to the front frame assembly with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48069 11.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C373262N01
0.573,0.667 0.729,0.865 0.156,0.198 10 false 1 1.25,0.354 1.396,0.5 0.146,0.146 10 true 2 2.76,0.802 2.906,0.948 0.146,0.146 10 false 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt (1), (2) : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt (3) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48068 12.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44250 13.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY

Hide 14.INSTALL FRONT STABILIZER BAR WITH BRACKET

Hide 15.INSTALL FRONT FRAME ASSEMBLY

a.

Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 16.REMOVE ENGINE HANGER (for 2GR-FKS)

Hide 45319 18.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)