Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2018.04–2021.02
RM33A0E _59 Vehicle Exterior _065390 WINDOW / GLASS _0327255 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-collision system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B485033

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B469635C01
1.208,0.75 1.563,0.594 false 1.51,0.979 2.417,0.615 2.417,0.615 2.094,1.031 false 1.792,1.01 2.406,0.625 false 0.063,0.073 0.417,0.271 0.354,0.198 12 false *A 2.469,0.51 2.781,0.667 0.313,0.156 10 false *a 1.604,0.51 1.917,0.667 0.313,0.156 10 false *b 0.844,0.781 0.969,0.958 0.125,0.177 10 true a
*A Back Side
*a Ceramic Notch
*b Windshield Glass Edge Side


Install the 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 14.7 mm (0.579 in.)


HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 75533G 3.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of a new windshield outside moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B469636C01
0.813,2.125 1.073,2.542 false 2.625,2.115 2.271,2.563 false 0.094,0.115 0.427,0.333 0.333,0.219 12 false *A 1.094,2.469 1.406,2.625 0.313,0.156 10 false *a 0.708,1.448 1.021,1.604 0.313,0.156 10 false *b 2.104,2.479 2.417,2.635 0.313,0.156 10 false *a 2.563,1.458 2.875,1.615 0.313,0.156 10 false *b 1.313,0.51 1.469,0.708 0.156,0.198 10 false A 1.292,1.01 1.417,1.177 0.125,0.167 10 true A 0.896,3.052 1.354,3.25 0.458,0.198 10 false A-A 2.021,3.115 2.177,3.313 0.156,0.198 10 false a
*A Back Side
*a Edge Of Curved Surface
*b Same Length


Install the new windshield outside moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 6.7 mm (0.264 in.)



Hide 56117A 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut 2 new window glass adhesive dams so that they are the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 72.3 to 72.7 cm (2.37 to 2.39 ft.)



b.

Using a brush or sponge, coat the installation area of the 2 new window glass adhesive dams with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



c.

Install the 2 window glass adhesive dams to the windshield glass as shown in the illustration.

B469637C01
5.458,1.813 5.917,2.323 false 1.073,3.25 1.188,3.385 false 1.063,0.625 1.177,0.76 false 0.115,0.115 0.542,0.417 0.427,0.302 12 false *A 5.958,2.271 6.271,2.427 0.313,0.156 10 false *b 0.927,3.146 1.24,3.302 0.313,0.156 10 false *a 1.438,1.438 1.594,1.635 0.156,0.198 10 false A 1.771,1.51 1.927,1.708 0.156,0.198 10 false A 4.948,1.167 5.406,1.365 0.458,0.198 10 false A-A 0.927,0.531 1.24,0.688 0.313,0.156 10 false *a
*A Back Side - -
*a Ceramic Notch *b Window Glass Adhesive Dam Positioning Center



d.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new window glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 129.6 to 130.0 cm (4.25 to 4.26 ft.)



e.

Using a brush or sponge, coat the installation area of the new window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



f.

Install the window glass adhesive dam to the windshield glass as shown in the illustration.

B469638C01
1.135,3.177 1.615,2.833 false 3.615,3.188 3.115,2.823 false 5.833,2.313 5.365,1.823 false 0.115,0.115 0.469,0.333 0.354,0.219 12 false *A 0.948,3.094 1.26,3.25 0.313,0.156 10 false *a 5.875,2.25 6.188,2.406 0.313,0.156 10 false *b 3.656,3.115 3.969,3.271 0.313,0.156 10 false *a 2.625,1.76 2.781,1.958 0.156,0.198 10 false A 2.615,2.115 2.771,2.313 0.156,0.198 10 false A 4.729,1.156 5.594,1.5 0.865,0.344 10 false A-A
*A Back Side - -
*a Ceramic Notch *b Window Glass Adhesive Dam Positioning Center



Hide 56153C 5.INSTALL FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B469639C01
0.083,0.073 0.469,0.406 0.385,0.333 12 false *A 0.542,1.938 0.698,2.135 0.156,0.198 10 false A 0.51,2.385 0.667,2.583 0.156,0.198 10 false A 1.219,2.979 1.677,3.177 0.458,0.198 10 false A-A 1.573,3.198 1.729,3.396 0.156,0.198 10 false a
*A Back Side
V100155

Glass Primer


Using a brush or sponge, coat the installation area of a new front window inner center moulding with glass primer.

Standard Dimension:
Area Dimension
a 18.4 to 21.4 mm (0.724 to 0.843 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the new front window inner center moulding to the windshield glass as shown in the illustration.

B469640C03
0.656,2.76 0.781,2.948 true 4.063,2.729 3.906,2.948 true 2.25,2.74 2.25,2.615 2.25,2.615 2.615,2.615 false 2.438,2.615 2.438,2.729 false 0.094,0.115 0.469,0.396 0.375,0.281 12 false *A 2.677,2.542 2.99,2.698 0.313,0.156 10 false *a 0.51,2.677 0.823,2.833 0.313,0.156 10 false *b 4.094,2.656 4.406,2.813 0.313,0.156 10 false *b 4.865,1.146 5.323,1.344 0.458,0.198 10 false A-A 5.354,2.323 5.51,2.521 0.156,0.198 10 false a 1.365,1.667 1.49,1.854 0.125,0.188 10 true A 1.323,2.042 1.448,2.229 0.125,0.188 10 true A
*A Back Side - -
*a Matchmark *b Ceramic Notch


Standard Dimension:
Area Dimension
a 0.6 mm (0.0236 in.)


NOTICE:

Do not damage the front window inner center moulding.



c.

Remove the matchmarks.


Hide 6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

a.
B469625C01
1.344,1.75 1.344,1.01 1.344,1.01 1.646,1.01 true 1.354,1.26 1.625,1.26 true 1.281,1.781 1.469,1.958 0.188,0.177 10 true *a
*a Matchmark


Position the windshield glass sub-assembly.

i.

Using suction cups, place the windshield glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the windshield glass sub-assembly and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with glass primer.

B469642C01
3.146,1.531 3.615,1.531 false 3.188,1.781 3.656,1.781 false 0.115,0.146 0.458,0.427 0.344,0.281 12 false *A 3.667,1.458 3.979,1.615 0.313,0.156 10 false *a 3.708,1.708 4.021,1.865 0.313,0.156 10 false *b 2.313,0.49 2.469,0.688 0.156,0.198 10 false B 2.333,0.792 2.49,0.99 0.156,0.198 10 true B 2.844,0.448 3,0.646 0.156,0.198 10 false A 2.865,0.729 3.021,0.896 0.156,0.167 10 true A 2.813,0.875 2.969,1.073 0.156,0.198 10 false C 3.094,0.813 3.25,1.01 0.156,0.198 10 false C 2.927,1.635 3.083,1.833 0.156,0.198 10 false D 2.948,2.104 3.104,2.302 0.156,0.198 10 false D 0.302,2.604 0.76,2.802 0.458,0.198 10 false A-A 2.521,2.552 2.979,2.75 0.458,0.198 10 false B-B 4.844,0.667 5.302,0.865 0.458,0.198 10 false C-C 4.24,2.49 4.698,2.688 0.458,0.198 10 false D-D 2.875,2.583 3.031,2.781 0.156,0.198 10 false a 4.885,2.542 5.042,2.74 0.156,0.198 10 false b
*A Back Side - -
*a Adhesive Application Area *b Ceramic Notch
V100155

Glass Primer - -


Standard Dimension:
Area Dimension
a 11.0 mm (0.433 in.) or more
b 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the windshield glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

B469643C01
3.135,1.469 3.563,1.469 false 3.188,1.792 3.615,1.792 false 2.854,0.458 3.01,0.656 0.156,0.198 10 false A 2.313,0.5 2.469,0.698 0.156,0.198 10 false B 2.823,0.896 2.979,1.094 0.156,0.198 10 false C 3.083,0.833 3.24,1.031 0.156,0.198 10 false C 2.917,1.646 3.073,1.844 0.156,0.198 10 false D 2.948,2.104 3.104,2.302 0.156,0.198 10 false D 2.875,0.75 2.99,0.896 0.115,0.146 10 true A 2.313,0.802 2.427,0.948 0.115,0.146 10 true B 0.365,2.51 0.823,2.708 0.458,0.198 10 false A-A 2.542,2.51 3,2.708 0.458,0.198 10 false B-B 4.833,0.438 5.292,0.635 0.458,0.198 10 false C-C 4.24,2.198 4.698,2.396 0.458,0.198 10 false D-D 1.354,3.531 1.51,3.729 0.156,0.198 10 false a 3.094,3.552 3.25,3.75 0.156,0.198 10 false b 4.823,2.469 4.979,2.667 0.156,0.198 10 false d 5.677,3.542 5.833,3.74 0.156,0.198 10 false e 6.021,0.552 6.177,0.75 0.156,0.198 10 false c 0.115,0.146 0.49,0.385 0.375,0.24 12 false *A 3.594,1.396 3.906,1.594 0.313,0.198 10 false *a 3.646,1.74 3.958,1.938 0.313,0.198 10 false *b
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 9.5 mm (0.374 in.)
b 9.5 mm (0.374 in.)
c 4.0 mm (0.158 in.)
d 8.0 to 11.0 mm (0.315 to 0.433 in.)
e 39.7 mm (1.56 in.)


HINT:

Apply adhesive to the ceramic notches.




e.
B469625C01
1.344,1.75 1.344,1.01 1.344,1.01 1.646,1.01 true 1.354,1.26 1.625,1.26 true 1.281,1.781 1.469,1.958 0.188,0.177 10 true *a
*a Matchmark


Install the windshield glass sub-assembly.

i.

Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass sub-assembly.




ii.

Lightly press the outer surface of the windshield glass sub-assembly to ensure that the windshield glass sub-assembly is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

When replacing the windshield glass sub-assembly or front window inner center moulding with a new one:

i.
B469641N01
2,2.052 2.125,2.229 0.125,0.177 10 true A 2.031,2.49 2.156,2.667 0.125,0.177 10 true A 0.802,3.01 1.26,3.208 0.458,0.198 10 false A-A

Remove the 2 protective retainers from the front window inner center moulding.

NOTICE:

Do not damage the front window inner center moulding.


HINT:

Make sure to remove the protective retainers.




g.

w/ Windshield Deicer System:

i.

Connect the connector.



h.

w/ Heated Windshield Defroster System:

i.

Connect each connector.



Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 8.INSTALL ROOF HEADLINING ASSEMBLY

Hide 89941 9.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 8646C 10.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

Hide 55708 12.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 13.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 14.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 15.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 16.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85292B 17.INSTALL FRONT WIPER ARM HEAD CAP

Hide 75536D 18.INSTALL WINDSHIELD OUTSIDE MOULDING LH

Hide 75535F 19.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.