Home › Engine / Hybrid System › 6AR-FSE (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072206 6AR-FSE INTAKE / EXHAUST _0353755 INTAKE MANIFOLD A

6AR-FSE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.

Install a new manifold gasket to the intake manifold.


b.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 6 bolts.


c.

Install a new EGR inlet gasket to the intake manifold.


d.

Install a new No. 2 EGR pipe gasket to the EGR valve assembly.


e.

Temporarily install the No. 2 EGR pipe to the EGR valve assembly and intake manifold with the 4 bolts.


f.
A413916N01
0.813,0.542 0.969,0.74 0.156,0.198 10 true 6 1.771,0.063 1.927,0.26 0.156,0.198 10 true 1 0.365,0.021 0.521,0.219 0.156,0.198 10 true 4 2.438,0.021 2.594,0.219 0.156,0.198 10 true 3 1.125,0.021 1.281,0.219 0.156,0.198 10 true 2 3.24,0.365 3.385,0.531 0.146,0.167 10 true 5

Tighten the 6 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


g.
A413910C01
1.24,0.771 1.427,0.958 0.188,0.188 10 true *a 2.271,1.417 2.458,1.615 0.188,0.198 10 true *b 2.104,0.594 2.292,0.792 0.188,0.198 10 true *b 0.521,1.552 0.708,1.74 0.188,0.188 10 true *a
*a Bolt (A)
*b Bolt (B)


Tighten the 4 bolts.

Torque:
Bolt (A) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)


h.

Engage the wire harness clamp to the No. 2 EGR pipe.


Hide 82121 2.CONNECT ENGINE WIRE

a.

Engage the 11 wire harness clamps and connect the engine wire.


b.

Connect the 4 connectors.


Hide 25860 4.INSTALL PURGE VALVE (PURGE VSV)

a.
A413918C01
1.542,2.885 1.927,2.885 true 0.844,1.948 1.229,1.948 true 1.156,0.823 1.375,1.354 1.375,1.354 1.573,1.354 true 1.948,2.802 2.146,2.979 0.198,0.177 10 true *1 0.677,1.865 0.865,2.042 0.188,0.177 10 true *2 0.552,0.604 0.76,0.781 0.208,0.177 10 false *a 1.219,3.229 1.427,3.406 0.208,0.177 10 false *b 1.073,1.344 1.271,1.542 0.198,0.198 10 false *c 0.948,1.177 1.135,1.365 0.188,0.188 10 false *d 2.708,1.26 2.906,1.469 0.198,0.208 10 false *e 2.719,4.292 2.906,4.469 0.188,0.177 10 false *f 1.594,1.26 1.813,1.469 0.219,0.208 10 false *g 0.521,3.74 0.729,3.917 0.208,0.177 10 false *a
*1 Fuel Vapor Hose
*2 Fuel Vapor Feed Hose Assembly
*a Left
*b Up
*c Rear
*d 60°
*e 4 to 9 mm (0.157 to 0.354 in.)
*f 2 to 7 mm (0.0787 to 0.276 in.)
*g Paint Mark


Install the purge valve (purge VSV) to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the purge valve (purge VSV) connector.


c.

Connect the fuel vapor feed hose assembly to the purge valve (purge VSV) and slide the clip to secure it.


d.

Connect the fuel vapor hose to the intake manifold and slide the clip to secure it.

HINT:

Make sure the direction of the clip is as shown in the illustration.



Hide 89421 5.INSTALL VACUUM SENSOR (MANIFOLD ABSOLUTE PRESSURE SENSOR)

a.

Install the vacuum sensor (manifold absolute pressure sensor) to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the vacuum hose to the intake manifold.


c.

Connect the vacuum sensor (manifold absolute pressure sensor) connector.


Hide 12262 6.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the intake manifold and slide the clip to secure it.


Hide 22030 7.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 53607A 8.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 55708 9.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY