Home › Engine / Hybrid System › 6AR-FSE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072206 6AR-FSE INTAKE / EXHAUST _0353756 EXHAUST MANIFOLD A

6AR-FSE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A413928

Using an E8 "TORX" socket wrench, install the stud bolt to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25586 3.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25051 4.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.

Install a new exhaust manifold gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold converter sub-assembly (TWC: Front Catalyst) to the cylinder head sub-assembly with the 5 nuts.


c.

Temporarily install the manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.


d.

Temporarily install the No. 2 manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.


e.

Install 2 new EGR cooler gaskets to the EGR pipe connector.


f.

Temporarily install the EGR pipe connector to the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly with the 4 bolts and nut.


g.
A413924N01
2,1.156 2.177,1.354 0.177,0.198 10 true 1 0.594,0.104 0.771,0.302 0.177,0.198 10 true 2 2.781,0.094 2.958,0.292 0.177,0.198 10 true 3 0.073,1.219 0.25,1.417 0.177,0.198 10 true 4 3.115,1.156 3.292,1.354 0.177,0.198 10 true 5

Tighten the 5 nuts in the order shown in the illustration.

Torque:
62 N*m (632 kgf*cm, 46 ft.*lbf)


h.
A413921C02
1.042,1.917 1.219,2.094 0.177,0.177 10 true *a 1.344,1.927 1.521,2.104 0.177,0.177 10 true *b 3,0.427 3.177,0.604 0.177,0.177 10 true *a 2.052,0.458 2.229,0.635 0.177,0.177 10 true *a
V100135

Bolt
V100136

Nut
*a Bolt (A)
*b Bolt (B)


Tighten the 4 bolts and nut.

Torque:
Bolt (A) and Nut : 36 N*m (367 kgf*cm, 27 ft.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17118 5.INSTALL MANIFOLD STAY

a.
A413922N01
1.031,1.323 1.219,1.531 0.188,0.208 10 true 1 2.094,1.688 2.302,1.906 0.208,0.219 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17139 6.INSTALL NO. 2 MANIFOLD STAY

a.
A415502

Tighten the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
A413935C01
2.292,0.969 2.521,1.167 0.229,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, tighten the nut.

Torque:
Specified tightening torque : 43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.8 N*m (385 kgf*cm, 28 ft.*lbf)




Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17410 10.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install 2 new gaskets to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C37
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Center Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and center exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Connect the heated oxygen sensor connector.


Hide 52239B 11.INSTALL BODY MOUNTING PLATE

Hide 57523A 12.INSTALL CENTER FLOOR CROSSMEMBER BRACE

Hide 57533B 13.INSTALL FRONT CENTER FLOOR BRACE

Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 16.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 17.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH