Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2018.04–2019.10
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0319848 AUTOMATIC TRANSAXLE ASSEMBLY A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 11361J 1.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A389112

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 4.DISCONNECT VACUUM HOSE

a.
C378077

Disconnect the vacuum hose from the rear engine mounting insulator.


b.
C378078

Disconnect the vacuum hose from the intake air surge tank assembly.


c.

Disengage the clamp to disconnect the vacuum hose from the hose clamp.


d.

Disengage the 9 clamps to disconnect the vacuum hose from the automatic transaxle assembly.

C378079


Hide 28100 5.REMOVE STARTER ASSEMBLY

Hide 35104V 6.REMOVE BREATHER PLUG HOSE

a.
C378088

Disengage the 3 hose clamps to disconnect the breather plug hose.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the breather plug hose from the No. 1 breather plug (ATM).

NOTICE:

Be careful not to damage the No. 1 breather plug (ATM).



c.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Remove the breather plug sub-assembly from the breather plug hose.

NOTICE:

Be careful not to damage the breather plug sub-assembly.



Hide 16261G 7.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
C378089

Disengage the 2 clamps to remove the transmission breather clamp.


b.
C378090

Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.



Hide 16260 8.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C378091

Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.



b.
C378092

Disengage the clamp to disconnect the water by-pass hose assembly from the automatic transaxle assembly.


Hide 9.DISCONNECT WIRE HARNESS

a.
C378080

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C378081

Disconnect the park/neutral position switch assembly connector.


c.
C378082

Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.


d.
C378083

Remove the 2 bolts.


e.
C378085

Remove the bolt.


f.

Disengage the 2 wire harness clamps to disconnect the wire harness.


g.
C378084

Remove the 2 bolts.


h.

for LHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C386779

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the 2 bolts to disconnect the wire harness.


iii.
C386780

Disengage the 3 wire harness clamps to disconnect the wire harness from the automatic transaxle assembly.



i.

for RHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C386781

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the bolt to disconnect the wire harness.


iii.
C386782

Disengage the 2 wire harness clamps to disconnect the wire harness.



Hide 51100G 11.REMOVE FRONT FRAME ASSEMBLY

Hide 12311A 12.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C378093

Remove the 3 bolts and front engine mounting bracket from the transaxle housing.


Hide 30500 13.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.

Support the automatic transaxle assembly with a transmission jack.

NOTICE:

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.



b.
C361050

Remove the 11 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 12372A 14.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C378094

Remove the 5 bolts and engine mounting insulator LH from the automatic transaxle case sub-assembly.


Hide 12303 16.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C378095

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.


Hide 32942 17.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 32941 18.DISCONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32907C 19.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 33493A 20.REMOVE TRANSMISSION OIL COOLER

Hide 21.REMOVE AUTOMATIC TRANSMISSION CASE COVER

a.
C378096

Remove the 2 clips and automatic transmission case cover from the automatic transaxle case sub-assembly.


Hide 33823 22.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C378097

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.


Hide 35150 23.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C378105

Remove the transmission case plug assembly from the transaxle housing.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 24.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C378099

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


b.
C378100

Remove the 2 bolts and 2 wire harness clamp brackets from the automatic transaxle case sub-assembly.


Hide 32000 25.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.


Hide 32101 27.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY