Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2018.04–2018.08
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319521 ENGINE ASSEMBLY A

A25A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.SECURE STEERING WHEEL

Hide 7.REMOVE FRONT WHEELS

Hide 53851M 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.

Remove the 3 screws and front wheel opening extension pad RH.


Hide 53852K 9.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.

Remove the 3 screws and front wheel opening extension pad LH.


Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.


Hide 11.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737B 12.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 2 screws, clip and front fender apron seal LH.


Hide 53736 13.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 2 screws, clip and front fender apron seal RH.


Hide 52119A 14.REMOVE FRONT BUMPER COVER

Hide 52618 15.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A406650

Remove the 4 bolts.


b.

Disengage the 2 claws to remove the front lower bumper absorber.


Hide 16.DRAIN ENGINE COOLANT

Hide 12601B 19.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A402166

Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17750A 20.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A402165

Remove the 2 bolts and inlet air cleaner assembly.


Hide 21.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A414502C01
2.24,3.5 2.25,4.021 2.25,4.021 1.802,3.25 false 1.167,4.292 1.167,4.094 false 2.208,4.052 2.521,4.25 0.313,0.198 10 false *a 1.094,4.313 1.406,4.51 0.313,0.198 10 false *a
*a Pin


Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 3 wire harness clamps.


c.

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


d.

Disengage the vacuum hose from the air cleaner hose.


e.

Lock the hose clip.


f.

Disengage the 3 pins and remove the air cleaner assembly with air cleaner hose.

NOTICE:

Make sure the 3 air cleaner supports remain attached to the vehicle body.



Hide 23.REMOVE BATTERY

Hide 74404A 24.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A402169

Disengage the 4 clamps from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly.


Hide 33820B 25.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C370840C01
2.031,2.01 1.906,2.01 1.906,2.01 1.677,2.333 false 2.052,1.896 2.271,2.094 0.219,0.198 10 false *a 2.938,3.083 3.156,3.281 0.219,0.198 10 false *b
*a Clip
*b 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.
C370853

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 23826 26.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A402171

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


Hide 44773F 27.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A402172

Slide the clip and disconnect the union to check valve hose from the vacuum pump assembly.


Hide 87246 28.DISCONNECT OUTLET HEATER HOSE

a.
A402655C02
1.802,1.177 2.021,1.417 2.021,1.417 2.208,1.417 false 2.26,1.333 2.5,1.542 0.24,0.208 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the outlet heater hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater hose connector with plastic bags to prevent damage and contamination.


Hide 87245 29.DISCONNECT INLET HEATER HOSE

a.
A402656C02
1.396,1.104 1.729,0.542 1.729,0.542 1.958,0.542 false 2.01,0.458 2.271,0.667 0.26,0.208 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the inlet heater hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater hose connector with plastic bags to prevent damage and contamination.


Hide 23901 30.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A402175

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


b.

Disconnect the fuel tube sub-assembly.

i.
A403472

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 16571C 31.DISCONNECT NO. 1 RADIATOR HOSE

a.
A402177

Remove the clamp to disconnect the No. 1 radiator hose from the No. 1 radiator bracket.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 32.DISCONNECT NO. 2 RADIATOR HOSE

a.
A402178

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 88711 33.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 34.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 35.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A402181

Remove the engine room relay block and junction block assembly cover from the engine room relay block and junction block assembly.


b.
A402182

Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the 4 connectors from the engine room relay block and junction block assembly.


d.

Using a screwdriver, disengage the claw and separate the wire harness from the engine room relay block and junction block assembly.


e.
A402183

Disengage the 3 clamps.


f.

Remove the nut and disconnect the wire harness from the positive (+) battery terminal.


g.

Remove the bolt and disconnect earth wire from the automatic transaxle assembly.


h.

Remove the bolt and disconnect the wire harness from the body.


Hide 16281F 36.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A402184

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


b.

Disengage the clamp.


Hide 45220 37.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 38.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 40.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A402185

Disengage the clamp.


c.

Remove the 6 bolts and body mounting plate.


d.
A402187

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


e.
A402186

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


f.
A402188C02
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 8 bolts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


g.

Remove the 4 bolts, 2 nuts and front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.


h.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 23825 41.REMOVE FUEL DELIVERY GUARD

a.
A402191

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 42.INSTALL ENGINE HANGERS

a.
A402192C01
0.479,0.542 0.656,0.542 0.656,0.542 0.885,0.854 true 2.313,0.25 2.49,0.25 2.49,0.25 2.719,0.563 true 2.063,0.177 2.281,0.365 0.219,0.188 10 true *2 0.25,0.438 0.458,0.635 0.208,0.198 10 true *1
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 43.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A402190

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101A 44.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 16261G 46.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 16260 47.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 45319 49.REMOVE STEERING GEAR HEAT INSULATOR

Hide 51100G 51.REMOVE FRONT FRAME ASSEMBLY

a.
A402195

Remove the bolt and separate the front engine mounting insulator from the front engine mounting bracket.


b.
A402196

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.


Hide 12361A 52.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A402197

Remove the 3 nuts and front engine mounting insulator from the front frame assembly.


Hide 12371A 53.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>REMOVAL

Hide 12311A 54.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C374392

Remove the 3 bolts and front engine mounting bracket from the transaxle housing.


Hide 11363A 55.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 32101 58.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 19315 59.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 82121 60.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 61.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 62.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 12305 63.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A414381

Disconnect the No. 6 water by-pass hose.


b.

Disengage the clamp.


c.

Remove the bolt, nut and the radiator reserve tank assembly.


d.
A402189

Remove the bolt and disconnect the bracket from the engine mounting insulator sub-assembly RH.


e.
A420753

Remove the bolt and disconnect the No. 1 bond cable from the engine mounting insulator sub-assembly RH.


f.
A402193

Disengage the clamp.


g.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.


Hide 12341 64.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A402194

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12304 65.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A428693

Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.


Hide 12372A 66.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL