52271D
1.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *A | Type A |
| *B | Type B |
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
Position the rear suspension member front body mounting cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
52271D
2.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
| *A | Type A |
| *B | Type B |
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
Position the rear suspension member front body mounting cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.
Install SST using the same procedure as for the rear suspension member front body mounting cushion (for LH Side).
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Perform the same procedure as for the rear suspension member front body mounting cushion (for LH Side).
Remove SST from the rear suspension member sub-assembly.
52276A
3.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
| *A | Type A |
| *B | Type B |
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.
Position the rear suspension member rear body mount cushion LH in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
52275B
4.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
| *A | Type A |
| *B | Type B |
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.
Position the rear suspension member rear body mount cushion RH in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.
Install SST using the same procedure as for the rear suspension member rear body mount cushion LH.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Using SST, install the rear suspension member rear body mount cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion RH.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Perform the same procedure as for the rear suspension member rear body mount cushion LH.
Remove SST from the rear suspension member sub-assembly.
48790
5.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
6.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
51206A
7.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
Install the 4 rear suspension member cushions to the rear suspension member sub-assembly.
When reusing the rear suspension member cushion, make sure to check its identification mark and install it to the correct position.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
Keep supporting the rear suspension member sub-assembly until the installation has been completed.
Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.
Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH, 2 bolts and 6 nuts.
48790
8.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Temporarily install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
9.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
10.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
11.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
12.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
13.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48258C
14.INSTALL REAR LOWER COIL SPRING INSULATOR LH
48258B
15.INSTALL REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48231B
16.INSTALL REAR COIL SPRING LH
48231A
17.INSTALL REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48812
18.INSTALL REAR STABILIZER BAR (for TMC Made)
48805
19.INSTALL REAR STABILIZER BAR SUB-ASSEMBLY (for TMR Made)
89408C
20.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
47319F
21.CONNECT REAR FLEXIBLE HOSE LH
Connect the rear flexible hose LH to the rear flexible hose bracket with the bolt.
47318F
22.CONNECT REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
23.STABILIZE SUSPENSION
48840A
24.INSTALL REAR STABILIZER LINK ASSEMBLY LH
48830D
25.INSTALL REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
26.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
27.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
28.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48730F
29.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
30.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
31.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
58398F
32.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)
58399D
33.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)
17420
34.INSTALL CENTER EXHAUST PIPE ASSEMBLY
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 6AR-FSE: Click hereEngine / Hybrid System>6AR-FSE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
35.INSTALL REAR WHEEL
48740F
36.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48730F
37.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
38.INSPECT FOR EXHAUST GAS LEAK
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 6AR-FSE: Click hereEngine / Hybrid System>6AR-FSE (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
39.INSPECT AND ADJUST REAR WHEEL ALIGNMENT