1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45250
2.INSTALL STEERING COLUMN ASSEMBLY
Make sure that the wire harness is not interfering with the steering column assembly.
Install the steering column assembly with the bolt and 2 nuts.
After the column is installed, check the tilt operation.
If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.
Tighten the nuts and check the tilt operation again.
Connect each connector and engage each wire harness clamp to the steering column assembly.
45220
3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
| *a | Matchmark |
Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.
Install the steering intermediate shaft assembly to the steering column assembly.
Install the bolt.
Tighten the clamp.
45253
4.INSTALL STEERING COLUMN HOLE COVER
Install the steering column hole cover with the 2 clips.
Install the clip.
Return the floor carpet.
45220
5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
6.INSTALL FRONT WHEEL LH (for LHD)
7.INSTALL FRONT WHEEL RH (for RHD)
87211
8.INSTALL NO. 1 AIR DUCT (for LHD)
Engage the 3 claws to install a new No. 1 air duct.
Install the 2 bolts.
87211
9.INSTALL NO. 1 AIR DUCT (for RHD)
Engage the 3 claws to install a new No. 1 air duct.
Install the 2 bolts.
73900
10.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
55302D
11.INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
w/ Driver Side Knee Airbag: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
w/o Driver Side Knee Airbag: : Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
55434B
12.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
55435B
13.INSTALL NO. 1 METER HOOD CLUSTER
53601
14.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55436B
15.INSTALL NO. 2 METER HOOD CLUSTER
55606
16.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55318C
17.INSTALL INSTRUMENT SIDE PANEL
62312B
18.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Install the front door opening trim weatherstrip.
After installation, check that the corners fit correctly.
62112A
19.INSTALL COWL SIDE TRIM SUB-ASSEMBLY
67914
20.INSTALL FRONT DOOR SCUFF PLATE
21.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.
| *a | Clamp |
Using pliers, expand the clamp.
While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
Return the clamp to its original position.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
89782
22.INSTALL TRANSPONDER KEY COIL (w/o Entry and Start System)
Engage the 2 claws to install the transponder key coil.
Connect the connector.
45286B
23.INSTALL UPPER STEERING COLUMN COVER
Engage the 2 claws and 4 clips to connect the upper steering column cover.
|
Install in this direction |
Engage the claw to install the upper steering column cover.
45024
24.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY
Engage the 2 claws to install the lower steering column cover sub-assembly.
Install the 3 screws.
25.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
84306
26.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
27.INSTALL STEERING WHEEL ASSEMBLY
28.CHECK STEERING WHEEL CENTER POINT
45130
29.INSTALL HORN BUTTON ASSEMBLY