Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2018.04–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0326605 AUTOMATIC TRANSAXLE ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Front bumper assembly (w/ Panoramic View Monitor System) Front television camera view adjustment Panoramic View Monitor System (Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 11361J 1.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C378399

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 28100 4.REMOVE STARTER ASSEMBLY

Hide 5.DISCONNECT WIRE HARNESS

a.
C378400

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C378401

Disconnect the park/neutral position switch assembly connector.


c.

for LHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C374274

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the 2 bolts to disconnect the wire harness.


iii.
C378402

Disengage the 2 wire harness clamps to disconnect the wire harness.



d.

for RHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C378403

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the bolt to disconnect the wire harness.


iii.
C378404

Disengage the wire harness clamp to disconnect the wire harness.



e.
C378405

Disengage the 2 wire harness clamps to disconnect the wire harness.


f.
C378407

Remove the 2 bolts to disconnect the 2 earth wires from the automatic transaxle assembly.


Hide 82824D 6.REMOVE WIRING HARNESS CONNECTOR

a.
C238952

Remove the 2 bolts.


b.

Remove the wiring harness connector from the transaxle case sub-assembly.


Hide 32942 7.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

Hide 32941 8.DISCONNECT INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

Hide 33493A 9.REMOVE TRANSMISSION OIL COOLER

Hide 32942 10.REMOVE OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

a.
C378408

Slide the clip and remove the outlet No. 1 oil cooler hose from the oil cooler tube union (outlet).

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler tube union (outlet).



Hide 32941 11.REMOVE INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

a.
C378426

Slide the clip and remove the inlet No. 1 oil cooler hose from the oil cooler tube union (inlet).

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and oil cooler tube union (inlet).



Hide 51100G 13.REMOVE FRONT FRAME ASSEMBLY

Hide 12311A 14.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C378409

Remove the 3 bolts and front engine mounting bracket from the transaxle housing.


Hide 30500 15.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.

Support the automatic transaxle assembly with a transmission jack.

NOTICE:

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.



b.
C201719

Remove the 9 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 12372A 16.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C378410

Remove the 4 bolts and engine mounting insulator LH from the transaxle case sub-assembly.


Hide 12371A 17.REMOVE REAR ENGINE MOUNTING INSULATOR

Hide 12303 18.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C378411

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.


Hide 33823 19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C378412

Remove the 2 bolts and No. 1 transmission control cable bracket from the transaxle case sub-assembly.


Hide 35150 20.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C378413

Remove the transmission case plug assembly from the transaxle housing.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 21.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C378414

Remove the bolt and wire harness clamp bracket from the transaxle case sub-assembly.


Hide 32000 22.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.


Hide 32101 24.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY