Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328637 INTAKE MANIFOLD A

2AR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Replacement of fuel injector assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 55708 1.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 2.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 3.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 23250 4.REMOVE FUEL INJECTOR ASSEMBLY

Hide 22030 5.REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 12262 6.DISCONNECT NO. 2 VENTILATION HOSE

a.
A407091

Slide the clip and disconnect the No. 2 ventilation hose from the intake manifold.


Hide 44774 7.DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.
A407092

Slide the clip and disconnect the union to connector tube hose from the intake manifold.


Hide 44773F 8.DISCONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.
A407092

Slide the clip and disconnect the union to check valve hose from the intake manifold.


Hide 17111 9.REMOVE INTAKE MANIFOLD

a.
A407094

Slide the clip and disconnect the fuel vapor feed hose from the intake manifold.


b.

Disengage the 3 wire harness clamps.


c.

Remove the bolt and wire harness clamp bracket from the intake manifold.


d.

w/ TCV:

i.
A199910N02
1.021,1.885 1.167,1.771 false 1.063,1.219 1.177,1.344 false 0.854,1.094 1.167,1.292 0.313,0.198 10 false M+ 0.833,1.833 1.146,2.031 0.313,0.198 10 false M-

Apply positive (+) battery voltage to terminal 8 (M-) and negative (-) battery voltage to terminal 4 (M+) of the sensor wire connector to close the 4 tumble control valves (TCV).

NOTICE:
·

The 4 tumble control valves (TCV) may be damaged if they are not closed before removing the intake manifold.

·

Apply battery voltage for 1 to 3 seconds.

·

If battery voltage is applied for more than 3 seconds, the intake air control valve actuator (for TCV) may be damaged.

·

Do not allow the lead wires to contact the other terminals.





e.
A407097C01
0.052,0.135 0.365,0.365 0.313,0.229 12 true *A 0.052,2.417 0.375,2.677 0.323,0.26 12 true *B
*A w/o TCV
*B w/ TCV


Remove the bolt and disconnect the engine wire.


f.

Disengage the 2 wire harness clamps.


g.

w/ TCV:

i.

Disconnect the intake air control valve actuator (for TCV) connector.



h.

w/o TCV:

i.
A254723

Remove the 6 bolts and intake manifold from the cylinder head sub-assembly.



i.
A254722

w/ TCV:

i.

Remove the 6 bolts and intake manifold from the cylinder head sub-assembly.

NOTICE:

The 4 tumble control valves (TCV) may be damaged if they are not closed before removing the intake manifold.


HINT:

Connect the battery to the terminals of the intake air control valve actuator (for TCV) to operate the motor and close the 4 tumble control valves (TCV).

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION




j.
A381762C01
0.083,0.083 0.427,0.365 0.344,0.281 12 false *A 0.115,2.5 0.5,2.792 0.385,0.292 12 false *B
*A w/o TCV
*B w/ TCV


Remove the intake manifold to head gasket from the intake manifold.


k.
A196049

Disconnect the 2 vacuum hoses and remove the No. 1 check valve from the intake manifold.


l.
A315821

Remove the bolt and wire harness clamp bracket from the intake manifold.