Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. REPAIR INSTRUCTION
75986B
3.INSTALL FRONT DOOR NO. 3 STRIPE
75976G
4.INSTALL FRONT DOOR NO. 2 STRIPE
75732A
5.INSTALL FRONT DOOR OUTSIDE MOULDING (w/ Outside Moulding)
75754A
6.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING
67852D
7.INSTALL FRONT DOOR REAR OUTSIDE SEAL
Engage the guide to install the front door rear outside seal.
75756C
8.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING
75792
9.INSTALL DOOR WINDOW FRAME MOULDING CLIP
|
Install in this Direction |
Engage the 2 claws to install the door window frame moulding clip.
67496A
10.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER
75720
11.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
67864B
12.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP
Engage the 8 clips to install the front door No. 2 weatherstrip.
67001A
13.INSTALL FRONT DOOR PANEL CUSHION
Engage the 2 claws to install new front door panel cushion.
67402F
14.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
|
Install in this Direction |
Engage the guide as shown in the illustration.
Install the front door front lower frame sub-assembly with the 2 bolts.
67664C
15.INSTALL DOOR FRAME GARNISH
Engage the 3 claws to install the door frame garnish.
67862
16.INSTALL FRONT DOOR WEATHERSTRIP
Engage the 25 clips and install the front door weatherstrip.
68620
17.INSTALL FRONT DOOR CHECK ASSEMBLY
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
|
Nut |
|
Bolt |
Install the front door check assembly with the 2 nuts and bolt.
69312
18.INSTALL FRONT DOOR LOCK OPEN ROD
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
69202A
19.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
| *A | Outside |
| *B | Inside |
Engage the claw as shown in the illustration.
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.
69040A
20.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69242E
21.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
Engage the 3 guides.
Engage the claw to install the front door rear outside handle pad.
69241H
22.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the front door front outside handle pad.
69217F
23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Engage the 2 guides and claw.
Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
Install the hole plug.
24.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.
Install the hole plug.
69220
25.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY
|
Install in this Direction |
Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.
Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, then slide the front door outside handle assembly toward the front of the vehicle to install it.
|
Engage in this Direction |
Move the lever as shown in the illustration and engage the 2 claws to secure the front door outside handle assembly.
Engage the 3 clamps.
Connect the connector.
Engage the 2 claws.
67404F
26.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Install in this Direction |
Engage the guide as shown in the illustration.
Install the front door rear lower frame sub-assembly with the 2 bolts.
68151C
27.INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
67856B
28.INSTALL FRONT DOOR PANEL PROTECTOR
Install the front door panel protector.
29.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the front door window regulator assembly.
Temporarily install the temporary bolt to the front door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the front door window regulator assembly with the 5 bolts.
Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
Connect the connector.
Engage the 2 claws to install the front door No. 2 service hole cover.
68102
30.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
for Driver Side:
Connect the multiplex network master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Move the front door window regulator assembly so that the door glass bolt holes can be seen.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
for Driver Side:
Disconnect the multiplex network master switch assembly.
for Front Passenger Side:
Disconnect the power window regulator switch assembly.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
Install the front door glass sub-assembly with the 2 bolts.
Install the hole plug.
89835
31.INSTALL DOOR SIDE AIRBAG SENSOR
67832
32.INSTALL FRONT DOOR SERVICE HOLE COVER
Engage the 3 clips to install the front door service hole cover.
Insert 4 front door weatherstrip clips and turn them 45 degrees as shown in the illustration to install them.
Engage the 2 clamps.
86160
33.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
34.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
87964
35.INSTALL OUTER MIRROR INSTALL HOLE COVER
36.INSTALL HOLE PLUG
89430A
37.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY
69206B
38.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 3 claws to install the front door inside handle sub-assembly.
67838A
39.INSTALL FRONT DOOR VENT SEAL
|
Install in this Direction |
Install the front door vent seal to the front door inner glass weatherstrip.
40.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL
|
Install in this Direction |
Install the front door inner glass weatherstrip with front door vent seal as shown in the illustration.
Engage the clip.
67602
41.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly as shown in the illustration.
Engage the guide and 7 claws.
Make sure to position each cable below the guide of the front door trim board sub-assembly as shown in the illustration.
Engage the 10 clips to install the front door trim board sub-assembly.
Install the 3 screws.
81230
42.INSTALL COURTESY LIGHT ASSEMBLY
74220
43.INSTALL FRONT ARMREST ASSEMBLY
|
Install in this Direction |
Engage the guide as shown in the illustration.
|
Install in this Direction |
Engage the 3 clips, 8 claws and 3 guides to install the front armrest assembly as shown in the illustration.
44.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Connect the connector.
|
Install in this Direction |
Engage the guide as shown in the illustration.
|
Install in this Direction |
Engage the 5 guides, 7 claws and clip to install the multiplex network master switch assembly with front door upper armrest base panel as shown in the illustration.
45.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Connect the connector.
|
Install in this Direction |
Engage the guide as shown in the illustration.
|
Install in this Direction |
Engage the 5 guides, 7 claws and clip to install the power window regulator switch assembly with front door upper armrest base panel as shown in the illustration.
74038A
46.INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Engage the 3 claws to install the front door armrest cover sub-assembly.
67492A
47.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
Engage the guide and clip to install the front door lower frame bracket garnish.
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 2AR-FE:
Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>INSTALLATION
for A25A-FKS:
Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>INSTALLATION
for 2GR-FKS:
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION
for 6AR-FSE:
49.INITIALIZE POWER WINDOW CONTROL SYSTEM
50.INSPECT POWER WINDOW OPERATION
51.INSPECT SRS WARNING LIGHT