Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2020.08
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0319789 TRANSMISSION WIRE A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.
C362373

Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.


b.

Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


d.

Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:
C362643C02
1.688,1.646 1.99,1.833 true 1.083,1.167 1.5,1.333 true 1.969,1.865 2.198,2.031 0.229,0.167 10 true *a 0.823,1.063 1.052,1.219 0.229,0.156 10 true *b
*a Transmission Wire (Temperature Sensor Wire)
*b Transmission Revolution Sensor (NC) Wire


To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.



e.
C365930

Connect the 9 solenoid valve connectors.

NOTICE:
C362374C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area.


·

To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.

·

To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.




f.
C365931

Engage the clamp to connect the transmission wire to the solenoid lock plate.


g.
C377490

Connect the transmission wire connector, rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 35151F 2.INSTALL TRANSMISSION CASE SIDE COVER

a.
C369219C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C369210N01
1.073,1.979 1.229,2.177 0.156,0.198 10 false A 2.792,0.063 2.948,0.26 0.156,0.198 10 false B 2.052,0.021 2.208,0.219 0.156,0.198 10 false C 1.365,0.01 1.521,0.208 0.156,0.198 10 false C 2.885,0.948 3.042,1.146 0.156,0.198 10 false C 2.823,1.49 2.979,1.688 0.156,0.198 10 false C 2.521,1.979 2.677,2.177 0.156,0.198 10 false C 1.969,1.979 2.125,2.177 0.156,0.198 10 false C 0.917,1.156 1.063,1.365 0.146,0.208 10 true C 0.917,0.625 1.063,0.823 0.146,0.198 10 true C

Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)).

NOTICE:

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.



c.

Temporarily install the 8 bolts (C).


d.
C369210N03
1.073,1.979 1.229,2.177 0.156,0.198 10 false 1 2.792,0.063 2.948,0.26 0.156,0.198 10 false 2 2.052,0.021 2.208,0.219 0.156,0.198 10 false 7 1.365,0.01 1.521,0.208 0.156,0.198 10 false 3 2.885,0.948 3.042,1.146 0.156,0.198 10 false 6 2.823,1.49 3.042,1.698 0.219,0.208 10 false 10 2.521,1.979 2.677,2.177 0.156,0.198 10 false 4 1.969,1.979 2.125,2.177 0.156,0.198 10 false 8 0.917,1.156 1.063,1.365 0.146,0.208 10 true 9 0.917,0.625 1.063,0.823 0.146,0.198 10 true 5

Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 32901C 3.INSTALL OIL COOLER UNION SUB-ASSEMBLY

a.
C378361C01
0.99,2.865 1.188,2.771 false 1.688,2.896 1.156,3.094 1.156,3.094 1.354,2.906 true 0.802,2.781 1.115,2.938 0.313,0.156 10 false *1 0.969,3.021 1.281,3.177 0.313,0.156 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly with the oil cooler union bolt.


b.

Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.


c.

Fully tighten the oil cooler union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)


d.

Fully tighten the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 51227B 4.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER

Hide 53737B 7.INSTALL FRONT FENDER APRON SEAL LH

Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 9.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 11.INSTALL FRONT WHEEL LH