Home › Engine / Hybrid System › M20A-FKS (LUBRICATION) › OIL PUMP › from 2021.02
RM33A0E _51 Engine / Hybrid System _098631 M20A-FKS LUBRICATION _0462221 OIL PUMP A

M20A-FKS LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11310 1.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 15104 3.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 13620B 5.REMOVE ENGINE BALANCER ASSEMBLY

Hide 15100 6.REMOVE OIL PUMP ASSEMBLY

a.
A402209

Remove the 3 bolts and oil pump assembly from the stiffening crankcase assembly.