Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2021.02
RM33A0E _51 Engine / Hybrid System _098627 M20A-FKS ENGINE MECHANICAL _0463498 CYLINDER HEAD GASKET A

M20A-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 16620D 3.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16207 4.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 5.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 16278B 6.REMOVE WATER HOSE CLAMP BRACKET

Hide 17167 7.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 9.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 22030 10.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 11.REMOVE THROTTLE BODY GASKET

Hide 25680 12.REMOVE EGR COOLER ASSEMBLY

Hide 25601 13.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25620 14.REMOVE EGR VALVE ASSEMBLY

Hide 16279 15.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 17138B 16.REMOVE INTAKE MANIFOLD STAY

Hide 23826 17.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

Hide 17177 19.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 20.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 21.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 22.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23.REMOVE NO. 1 WATER BY-PASS HOSE ASSEMBLY

Hide 23807 24.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23291 26.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 28.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 30.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452D 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 35.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 36.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 37.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 38.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 39.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 40.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 29300 41.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 42.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 44.REMOVE WATER BY-PASS OUTLET SUB-ASSEMBLY

Hide 11201 45.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 46.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 47.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 48.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 49.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 50.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 51.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 52.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 54.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 55.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 56.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 57.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 58.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 59.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 60.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13501A 62.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13502B 63.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13801 64.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 65.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 67.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 68.REMOVE CYLINDER HEAD GASKET

A426101

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 69.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 70.INSPECT CYLINDER HEAD SUB-ASSEMBLY