Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2021.02
RM33A0E _58 Vehicle Interior _065389 INTERIOR PANELS / TRIM _0325686 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REASSEMBLY  


PROCEDURE

Hide 69550A 1.INSTALL GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY (w/ Glove Compartment Door Lock Cylinder Assembly)

a.
B575728C01
2.875,3.063 2.875,3.198 true 1.792,2.99 1.792,3.125 true 0.625,3.042 0.625,3.177 true 2.813,3.208 3.125,3.365 0.313,0.156 10 false *a 1.719,3.125 2.031,3.281 0.313,0.156 10 false *a 0.542,3.198 0.854,3.354 0.313,0.156 10 false *a
*a Cylinder Lock Plate
V113147

Install in this Direction


With the cylinder lock plate pressed, insert the glove compartment door lock cylinder assembly into the glove compartment door lever to install it as shown in the illustration.

NOTICE:

After installing the glove compartment door lock cylinder assembly, lift the glove compartment door lever and confirm that the cylinder lock plate is correctly protruding and that the glove compartment door lock cylinder assembly does not move even when pushed from the rear.



Hide 2.INSTALL INSTRUMENT PANEL CUSHION

a.

Clean the instrument panel safety pad sub-assembly surface.

i.

Remove any remaining double-sided tape from the instrument panel safety pad sub-assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new instrument panel cushion.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B469295C01
0.708,1.052 0.542,0.896 false 2.688,1.052 2.833,0.938 true 0.656,3.094 0.302,3.021 true 0.75,0.99 1.063,1.146 0.313,0.156 10 false *a 2.51,0.99 2.781,1.146 0.271,0.156 10 false *a 0.698,3.021 1.01,3.177 0.313,0.156 10 false *b
*a Edge of Curved Surface
*b Outline


Install the instrument panel cushion as shown in the illustration.


Hide 82144 3.INSTALL NO. 4 INSTRUMENT PANEL WIRE (w/ Ion Generator)

a.
B482078

Engage the 2 clamps to install the No. 4 instrument panel wire.


Hide 4.INSTALL ION GENERATOR WITH BRACKET (w/ Ion Generator)

Hide 87201N 5.INSTALL AIR DUCT SUB-ASSEMBLY (w/ Ion Generator)

Hide 86101 6.INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)

Hide 86101 7.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)

Hide 55328 8.INSTALL NO. 1 INSTRUMENT PANEL PIN

a.
B469293

Install the 4 No. 1 instrument panel pins with the 4 screws <E>.


Hide 9.INSTALL INSTRUMENT PANEL HOLE COVER (w/ Headup Display)

a.
B480820

Engage the 3 guides.


b.
B480819

Engage the 5 claws to install the instrument panel hole cover.


Hide 55981 10.INSTALL NO. 1 DEFROSTER NOZZLE GARNISH

a.

Engage the 5 guides.

B469292


b.

Engage the 4 clips to install the No. 1 defroster nozzle garnish.

B469291


Hide 83107A 11.INSTALL NO. 1 METER BRACKET SUB-ASSEMBLY

a.
B469290

Install the No. 1 meter bracket sub-assembly with the screw <E>.


Hide 83107B 12.INSTALL NO. 2 METER BRACKET SUB-ASSEMBLY (w/ Headup Display)

a.
B480816

Install the No. 2 meter bracket sub-assembly with the screw <E>.


Hide 55417B 13.INSTALL RADIO TUNER FINISH RETAINER

a.
B606528

Install the radio tuner finish retainer with the 5 screws <E>.


Hide 82143 14.INSTALL NO. 3 INSTRUMENT PANEL WIRE

a.
B606527

Engage the clamp to install the No. 3 instrument panel wire.


Hide 89120A 15.INSTALL AUTOMATIC LIGHT CONTROL SENSOR

Hide 86681B 16.INSTALL ANTENNA DIVIDER (w/ Antenna Divider)

Hide 17.INSTALL NAVIGATION ANTENNA ASSEMBLY WITH BRACKET (w/ Navigation Antenna)

Hide 55086 18.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B606472

Install the No. 3 heater to register duct sub-assembly with the 2 screws <E>.


Hide 55084E 19.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B606471

Install the No. 1 heater to register duct sub-assembly with the 2 screws <E>.


Hide 83108 20.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 55950G 21.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.
B606470

Install the defroster nozzle assembly with the 3 screws <E>.


Hide 55972C 22.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT

a.
B469283C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


b.
B469281C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


c.

Install the No. 2 side defroster nozzle duct with the 2 screws <E>.


Hide 55971C 23.INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT

a.
B469279C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


b.
B469277C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


c.

Install the No. 1 side defroster nozzle duct with the screw <E>.


Hide 73960A 24.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY