Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL INJECTOR (for Direct Injection) › from 2021.02
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0319393 FUEL INJECTOR(for Direct Injection) A

A25A-FKS FUEL  FUEL INJECTOR(for Direct Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during direct fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of direct fuel injector assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)for A25A-FKS (w/ Canister Pump Module)
(Click here)for A25A-FKS (w/o Canister Pump Module)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25620 4.REMOVE EGR VALVE ASSEMBLY

Hide 23801P 6.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23814B 7.REMOVE FUEL DELIVERY PIPE

NOTICE:

When replacing the fuel delivery pipe, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.
A401658

Disconnect the fuel pressure sensor connector.


b.

Disengage the clamp to disconnect the sensor wire from the fuel delivery pipe.


c.
A401659

Disconnect the 4 direct fuel injector assembly connectors.

NOTICE:

Make sure to disconnect the connectors carefully.



d.
A401660

Remove the 4 bolts and fuel delivery pipe with the 4 direct fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:
·

Make sure not to touch or strike the tips of the direct fuel injector assemblies.

·

Pull and remove the fuel delivery pipe in a straight line without tilting it.




Hide 23250E 8.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

a.
A401662N01
2.031,2.052 2.802,2.25 0.771,0.198 10 false No. 3

Secure the fuel delivery pipe in a vise between aluminum plates and pull out the 4 direct fuel injector assemblies.

NOTICE:
·

Pull and remove each direct fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe O-ring.

·

After removing the direct fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe side.

·

Attach a tag or label with the corresponding cylinder number to each direct fuel injector assembly so that they can be installed to their original locations.

·

Cover the tip of each direct fuel injector assembly to prevent it from being damaged.




b.

Remove the nozzle holder clamp from each direct fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each direct fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each direct fuel injector assembly.


e.

Remove the C-ring and injector vibration insulator from each direct fuel injector assembly.


Hide 23255A 9.REMOVE FUEL INJECTOR SEAL

a.
A401663

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the direct fuel injector assembly.

·

If a direct fuel injector assembly is dropped or the tip of the direct fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each direct fuel injector assembly.