Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.02
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319522 ENGINE UNIT A

A25A-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 25861A 1.INSTALL NO. 2 VACUUM SWITCHING VALVE BRACKET

a.

Using an 8 mm socket wrench, install the No. 2 vacuum switching valve bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17169A 3.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Type A:

i.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



b.

Type B:

i.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



Hide 16323 4.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.

Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16031 5.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 11452 6.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250E 9.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23250F 11.INSTALL PORT FUEL INJECTOR ASSEMBLY

Hide 23291 13.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23800 15.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 16.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82126A 17.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 18.INSTALL SENSOR WIRE

a.

Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 3 clamps.


c.

Connect the 4 connectors.


Hide 16295 19.INSTALL NO. 7 WATER BY-PASS HOSE

a.

Install the No. 7 water by-pass hose and slide the 2 clips to secure it.


Hide 23100X 20.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 21.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 22.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 23.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A476751C01
2.792,2.729 2.833,2.365 2.833,2.365 2.979,2.365 false 3.042,2.292 3.354,2.49 0.313,0.198 10 false *a 1.552,2.354 1.865,2.552 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Using an 8 mm socket wrench, install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17177 25.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 16278 27.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install the bolt (A).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.
A473526N02
0.396,1.125 0.76,1.323 0.365,0.198 10 true 2 (B) 0.906,1.948 1.229,2.146 0.323,0.198 10 true 1 (B) 2.073,1.917 2.292,2.135 0.219,0.219 10 true A

Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16279 28.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.


b.

Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25620 29.INSTALL EGR VALVE ASSEMBLY

a.
A472909C01
2.115,0.844 2.323,0.552 2.323,0.552 2.448,0.552 true 2.094,1.021 2.313,1.021 true 2.396,0.917 2.708,1.115 0.313,0.198 10 true *a 2.51,0.438 2.823,0.635 0.313,0.198 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve assembly to the pin of the camshaft housing sub-assembly.


b.

Using an 8 mm socket wrench, install the EGR valve assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


Hide 30.INSTALL WATER HOSE

a.

Connect the water hose to the EGR valve assembly and slide the clip to secure it.


Hide 25601 31.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly, a new EGR inlet gasket and a new EGR valve adapter gasket with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25680 32.INSTALL EGR COOLER ASSEMBLY

a.
A472569C02
1.156,1.906 0.792,2.021 0.792,2.021 1.042,1.813 false 0.917,1.604 0.542,1.417 0.542,1.417 0.979,1.458 false 2.458,0.635 2.458,1.104 2.458,1.104 2.146,0.708 false 2.427,0.385 2.021,0.177 2.021,0.177 2.125,0.469 false 0.313,1.292 0.594,1.573 0.281,0.281 10 false *a 0.573,1.979 0.823,2.177 0.25,0.198 10 false *a 2.448,1.146 2.698,1.344 0.25,0.198 10 false *a 1.781,0.073 2.104,0.344 0.323,0.271 10 false *a
*a Claw


Install a new EGR cooler gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side.



b.

Install a new EGR valve gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR cooler assembly side.



c.

Type A:

i.
A472904C02
1.677,1.823 1.833,2.021 0.156,0.198 10 true 1 2.573,1.927 2.729,2.125 0.156,0.198 10 true 3 2.885,1.063 3.042,1.26 0.156,0.198 10 true 2 1.708,0.167 1.865,0.365 0.156,0.198 10 true 4 0.698,0.104 0.854,0.302 0.156,0.198 10 false 5
V100135

Bolt
V100136

Nut


Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 2 bolts and 3 nuts.


ii.

Tighten the 2 bolts and 3 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



d.

Type B:

i.
A472905C02
1.656,1.802 1.813,2 0.156,0.198 10 true 1 2.875,1.042 3.031,1.24 0.156,0.198 10 true 2 2.583,1.917 2.74,2.115 0.156,0.198 10 true 3 1.76,0.26 1.917,0.458 0.156,0.198 10 true 4 0.646,0.125 0.802,0.323 0.156,0.198 10 true 5
V100135

Bolt
V100136

Nut


Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 3 bolts and 2 nuts.


ii.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



e.

Connect the No. 3 water by-pass hose to the EGR cooler assembly.


f.

Connect the water hose to the EGR cooler assembly.


Hide 22271 33.INSTALL THROTTLE BODY GASKET

Hide 22030 34.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17141 35.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 17167 37.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Type A:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

Type B:

i.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 16260 38.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A402665C01
1.479,3.854 1.292,3.854 1.292,3.854 1.042,3.344 false 1.521,3.76 1.833,3.917 0.313,0.156 10 false *a 2.969,2.906 3.281,3.063 0.313,0.156 10 false *b 2.969,3.573 3.281,3.729 0.313,0.156 10 false *b
*a Paint Mark
*b 45° (Claw of Clip Location)


Connect the flow shutting valve (water by-pass hose assembly) to the outlet water by-pass sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the outlet water by-pass sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




b.

Install the water hose clamp bracket with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Connect the flow shutting valve (water by-pass hose assembly) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16207 39.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.


Hide 11323C 40.INSTALL NO. 3 TIMING CHAIN COVER (w/ Cover)

a.

Using an 8 mm socket wrench, install the No. 3 timing chain cover and plate washer to the No. 2 timing gear cover assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11336A 41.INSTALL TIMING GEAR COVER INSULATOR

a.

Using an 8 mm socket wrench, install the timing gear cover insulator and plate washer to the No. 2 timing gear cover assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11336A 42.INSTALL NO. 2 TIMING CHAIN COVER INSULATOR

a.

Install the No. 2 timing chain cover insulator to the V-ribbed belt tensioner assembly.


Hide 16620D 43.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



If oil or grease is on the location indicated by the arrow, replace the belt tensioner.

a.

Install the V-ribbed belt tensioner assembly to the No. 2 timing gear cover assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12602C 44.INSTALL NO. 2 ENGINE COVER

a.

Install the No. 2 engine cover to the No. 2 timing gear cover assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 88310 45.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

a.

for Type A:

i.

Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with pulley with the 2 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.
E365913C02
1,0.167 1.167,0.333 0.167,0.167 10 true 1 1.917,1.917 2.083,2.083 0.167,0.167 10 true 2 0.885,1.781 1.052,1.948 0.167,0.167 10 true 3 2.083,0.167 2.25,0.333 0.167,0.167 10 true 4
V100135

Bolt
V100136

Nut


Install the compressor assembly with pulley with the 2 bolts and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and nuts in the order shown in the illustration.




b.

for Type B:

i.
E371401N01
0.885,0.052 1.042,0.25 0.156,0.198 10 true 1 1.219,1.917 1.375,2.115 0.156,0.198 10 true 2 0.635,1.76 0.792,1.958 0.156,0.198 10 true 3 1.635,0.115 1.792,0.313 0.156,0.198 10 true 4

Install the compressor assembly with pulley with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.




Hide 16361A 47.INSTALL V-RIBBED BELT

Hide 43457 48.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:

Make sure that the bolts and bolt holes are free of oil. Clean them if necessary.