Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › 2017.09–2019.02
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319556 SHIFT LEVER A

P710 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

a.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


b.

Connect the shift lock control ECU connector.


c.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


d.

Connect the transmission control switch connector.


e.

Install the clip to the No. 1 console box duct.


f.
C380394N01
2.688,1.083 2.844,1.281 0.156,0.198 10 true 1 0.635,1.667 0.792,1.865 0.156,0.198 10 true 2 2.104,1.781 2.26,1.979 0.156,0.198 10 true 3 2.354,0.625 2.51,0.823 0.156,0.198 10 true 4

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


g.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.


a.
C194520C31
2.271,2.573 2.615,2.573 false 1.948,1.75 2.083,1.531 2.083,1.531 2.188,1.531 false 1.594,0.958 1.781,1.135 0.188,0.177 10 false *c 1.792,1.344 1.979,1.521 0.188,0.177 10 false *c 2.438,0.781 2.625,0.958 0.188,0.177 10 false *d 2.25,1.458 2.51,1.656 0.26,0.198 10 false *a 2.229,2.313 2.417,2.49 0.188,0.177 10 false *d 2.656,2.49 2.958,2.729 0.302,0.24 10 false *b
*a Slider
*b Lock Piece
*c Slide
*d Pull


Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.


b.
C377530C01
2.208,3.344 2.938,2.125 2.938,2.125 2.25,1.198 true 1.938,1.833 2.167,2.156 2.167,2.156 2.333,2.156 false 1.938,4.063 2.167,4.385 2.167,4.385 2.333,4.385 false 2.375,2.063 2.677,2.313 0.302,0.25 10 false *a 2.042,0.458 2.333,0.667 0.292,0.208 10 false *b 3,2.042 3.26,2.219 0.26,0.177 10 false *c 2.375,4.302 2.677,4.552 0.302,0.25 10 false *a
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


c.
C380402C01
0.5,0.323 0.635,0.323 0.635,0.323 0.823,0.51 true 2.281,0.219 2.417,0.219 2.417,0.219 2.604,0.406 true 0.344,0.229 0.573,0.438 0.229,0.208 10 false *a 2.115,0.125 2.344,0.333 0.229,0.208 10 false *a
*a Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:

After installation, check that the outer part of the stopper is as shown in the illustration.



d.
C380403C01
1.167,2.5 1.302,2.5 1.302,2.5 1.406,2.667 false 2.063,2.771 2.177,2.552 2.177,2.552 2.313,2.552 false 1.01,2.406 1.25,2.635 0.24,0.229 10 false *a 2.354,2.448 2.635,2.698 0.281,0.25 10 false *b
*a Lock Piece
*b Adjuster Case


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Check that the lock piece is pulled out.

·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.




e.
C296262C01
2.229,0.854 2.365,0.563 2.365,0.563 2.5,0.563 false 1.24,3.219 1.375,2.927 1.375,2.927 1.51,2.927 false 1.208,0.667 1.344,0.375 1.344,0.375 1.479,0.375 false 2.24,3.323 2.375,3.031 2.375,3.031 2.51,3.031 false 1.531,0.281 1.813,0.51 0.281,0.229 10 false *a 1,2.76 1.271,3.01 0.271,0.25 10 false *b 2.552,0.469 2.854,0.698 0.302,0.229 10 false *c 1.552,2.833 1.833,3.063 0.281,0.229 10 false *a 2.542,2.938 2.844,3.167 0.302,0.229 10 false *c
*a Lock Piece
*b Push in
*c Adjuster Case


Push the lock piece into the adjuster case.

NOTICE:
·

Check that the shift lever is in N.

·

Securely push in the lock piece until the slider lock is engaged.




f.

After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.


Hide 33504F 4.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 33554C 5.INSTALL SHIFT LOCK RELEASE BUTTON COVER

a.
C370835

Engage the 2 claws and guide to install the shift lock release button cover to the rear upper console panel sub-assembly.