The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
64718C
3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER
4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
22030
5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
25620
6.REMOVE EGR VALVE ASSEMBLY
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE
23910A
8.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
23801P
9.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
Disconnect the ignition coil connector.
for EGR Valve Bracket Connection Type:
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
for Cylinder Head Cover Sub-assembly Connection Type:
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
Using an 8 mm socket wrench, remove the bolt.
Loosen the 2 bolts of the fuel pump assembly.
Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.
23800
10.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY
Disconnect the No. 5 engine wire connector.
Remove the 2 bolts and fuel delivery pipe with sensor assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.
Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.
23807V
11.REMOVE NO. 1 DELIVERY PIPE SPACER
Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.
23291
12.REMOVE INJECTOR VIBRATION INSULATOR
Remove the 4 injector vibration insulators from the cylinder head sub-assembly.
82125N
13.REMOVE NO. 5 ENGINE WIRE
Disconnect the 4 port fuel injector assembly connectors and fuel pressure sensor connector.
Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe with sensor assembly.
23250F
14.REMOVE PORT FUEL INJECTOR ASSEMBLY
Pull the 4 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.
Remove the O-ring from each port fuel injector assembly.
Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.
Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.