This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
17169A
1.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Type A:
Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.
Type B:
Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.
11452
2.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the camshaft housing sub-assembly with the bolt.
Install the engine oil level dipstick.
19500
3.INSTALL IGNITION COIL ASSEMBLY
23255A
4.INSTALL FUEL INJECTOR SEAL
23250E
5.INSTALL DIRECT FUEL INJECTOR ASSEMBLY
23814B
6.INSTALL FUEL DELIVERY PIPE
23250F
7.INSTALL PORT FUEL INJECTOR ASSEMBLY
82125N
8.INSTALL NO. 5 ENGINE WIRE
23291
9.INSTALL INJECTOR VIBRATION INSULATOR
23807V
10.INSTALL NO. 1 DELIVERY PIPE SPACER
23800
11.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY
12.INSTALL WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.
82126A
13.INSTALL NO. 6 ENGINE WIRE
Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.
Engage the 2 clamps.
Connect the 4 connectors.
82219A
14.INSTALL SENSOR WIRE
Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Engage the 3 clamps.
Connect the 4 connectors.
16295
15.INSTALL NO. 7 WATER BY-PASS HOSE
Install the No. 7 water by-pass hose and slide the 2 clips to secure it.
23100X
16.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
23801P
17.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
23100X
18.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
23801P
19.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
for EGR Valve Bracket Connection Type:
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
for Cylinder Head Cover Sub-assembly Connection Type:
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using an 8 mm socket wrench, install the bolt.
23910A
20.CONNECT FUEL TUBE SUB-ASSEMBLY
17177
21.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
17111
22.INSTALL INTAKE MANIFOLD
16278
23.INSTALL NO. 2 WATER BY-PASS PIPE
Install the bolt (A).
Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.
16279
24.INSTALL NO. 3 WATER BY-PASS PIPE
Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.
Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.
25620
25.INSTALL EGR VALVE ASSEMBLY
Using an 8 mm socket wrench, install the EGR valve bracket with the bolt.
for EGR Valve Bracket Connection Type:
| *a | Pin |
| *b | Hole |
Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.
Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.
Using the 8 mm socket wrench, connect the No. 1 fuel pipe sub-assembly to the EGR valve bracket with the bolt.
for Cylinder Head Cover Sub-assembly Connection Type:
| *a | Pin |
| *b | Hole |
Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.
Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.
Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.
26.INSTALL WATER HOSE
w/ Water Hose Connector:
| *a | Retainer |
|
Push in |
Connect the water hose to the EGR valve assembly.
Align the water hose with the EGR valve assembly, push the water hose onto the EGR valve assembly, then push in the retainer to secure the connection.
Confirm that the retainer makes a "click" sound when pushed.
Check that the EGR valve assembly and water hose are securely connected by pulling on them.
w/o Water Hose Connector:
Connect the water hose to the EGR valve assembly and slide the clip to secure it.
25601
27.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
25680
28.INSTALL EGR COOLER ASSEMBLY
Install the EGR cooler assembly, a new EGR cooler gasket and a new EGR valve gasket with the 5 bolts.
Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.
Connect the water hose to the EGR cooler assembly and slide the clip to secure it.
22271
29.INSTALL THROTTLE BODY GASKET
22030
30.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17141
31.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)
17118
32.INSTALL MANIFOLD STAY
17167
33.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.
16260
34.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Install the water hose clamp bracket with the 2 bolts as shown in the illustration.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).
| *a | Paint Mark |
| *b | 45° (Claw of Clip Location) |
Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.
Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.
Make sure that the claws of the clip are within the location shown in the illustration.
Connect the flow shutting valve (water by-pass hose assembly) with the bolt.
16207
35.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the No. 2 water by-pass pipe sub-assembly with the bolt.
Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.
88370
36.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.
|
Bolt |
|
Nut |
Install the compressor with motor assembly with the bolt and 2 nuts.
Tighten the bolt and nuts in the order shown in the illustration.
43457
37.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.
Make sure that the bolts and bolt holes are free of oil. Clean them if necessary.