Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2017.09–2019.10
RM33C0E _51 Engine / Hybrid System _065423 A25A-FXS INTAKE / EXHAUST _0322981 EXHAUST MANIFOLD A

A25A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 6 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst), No. 1 exhaust manifold heat insulator and No. 1 upper front floor heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A402303N02
1.573,0.969 1.729,1.167 0.156,0.198 10 false 1 2.073,0.698 2.229,0.896 0.156,0.198 10 true 1 1.125,0.083 1.271,0.25 0.146,0.167 10 true 2 2.469,0.063 2.615,0.25 0.146,0.188 10 true 3 1.594,0.698 1.74,0.885 0.146,0.188 10 true 4 2.719,0.292 2.854,0.469 0.135,0.177 10 true 5 0.99,0.76 1.125,0.927 0.135,0.167 10 true 6 0.542,0.24 0.677,0.406 0.135,0.167 10 true 7

Using a 12 mm deep socket wrench, temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.


d.

Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A402302N02
2.771,1.427 2.927,1.625 0.156,0.198 10 true 1 0.375,1.063 0.531,1.26 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402305C02
2.365,0.417 2.573,0.615 0.208,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)




Hide 58151 5.INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

a.
A402306C02
1.438,1.438 1.615,1.635 0.177,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.

Torque:
Specified tightening torque : 4.9 N*m (50 kgf*cm, 43 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 4.3 N*m (44 kgf*cm, 38 in.*lbf)




Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 53607A 8.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 9.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 55708 10.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 58152A 11.INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install 2 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) and center exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.

Engage the wire harness clamp.


e.

Connect the air fuel ratio sensor (for sensor 2) connector.


Hide 57523A 13.INSTALL CENTER FLOOR CROSSMEMBER BRACE

Hide 57533B 14.INSTALL FRONT CENTER FLOOR BRACE

Hide 58166A 15.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 16.INSTALL FRONT FLOOR COVER RH (w/ Cover)

Hide 18.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 51441 19.INSTALL NO. 1 ENGINE UNDER COVER (w/ Cover)

Hide 53852K 20.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (w/ Cover)

Hide 53851M 21.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (w/ Cover)