Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


When troubleshooting a vehicle with a diagnosis system, the only difference from the usual troubleshooting procedure is connecting the GTS to the vehicle and reading various data output from the skid control ECU (brake booster with master cylinder assembly).

The skid control ECU (brake booster with master cylinder assembly) records DTCs when it detects a malfunction in itself or in its circuits.

To check for DTCs, connect the GTS to the DLC3 on the vehicle. The GTS can be used to clear the DTCs, activate various actuators, and check the Freeze Frame Data and Data List.

a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge the auxiliary battery before proceeding to the next step.




DIAGNOSIS


a.

If the skid control ECU (brake booster with master cylinder assembly) detects a malfunction, the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights will come on in order to warn the driver. Also, if the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operated indicator light blinks.

Vehicle Conditions:

(a)

The driver side door is closed.

(b)

The driver side seat belt is fastened.




b.

DTCs are simultaneously stored in memory.

The DTCs can be read by connecting the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR




DTC FOR RELATED SYSTEM MALFUNCTION


a.

When the skid control ECU (brake booster with master cylinder assembly) detects DTCs stored by related systems, it stores DTCs to indicate the malfunctioning system.

DTC for Related System Malfunction
Malfunctioning System Output DTC DTC Storage System/Control Condition
Hybrid control system DTC C1310 (INF code 1140) Current and history DTCs are cleared when the system returns to normal. VSC system is disabled
DTC C1310 (INF code 1141) Brake hold control operation is prohibited
Electric parking brake system DTC C13AF
DTC U0128
Current DTCs are cleared when the system returns to normal. Brake hold control operation is prohibited
Airbag system DTC C147D
DTC U0151
Current DTCs are cleared when the system returns to normal. Secondary collision brake control operation is prohibited

HINT:

The above DTCs may be stored in the skid control ECU (brake booster with master cylinder assembly) even if it was never stored as a history DTC or cleared in the system that caused the DTC to be stored.




WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK


a.

When the power switch is turned on (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction), VSC OFF indicator, slip indicator, brake hold standby indicator and brake hold operated indicator lights all come on for approximately 3 seconds.

HINT:
·

When the brake fluid level is low, the brake warning light / red (malfunction) comes on.

·

If the warning light and indicator light check results are not normal, proceed to troubleshooting for the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction), VSC OFF indicator, slip indicator, brake hold standby indicator and brake hold operated indicator light circuits.

·

If an indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.



Trouble Area See Procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake warning light / red (malfunction) circuit (Remains on) (Click here)
Brake warning light / red (malfunction) circuit (Does not come on) (Click here)
Brake warning light / yellow (minor malfunction) circuit (Remains on) (Click here)
Brake warning light / yellow (minor malfunction) circuit (Does not come on) (Click here)
VSC OFF indicator light circuit (Remains on) (Click here)
VSC OFF indicator light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)
Brake hold standby indicator light circuit (Click here)
Brake hold operated indicator light circuit (Click here)