Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Hold Operated Indicator Light Circuit  


DESCRIPTION

The brake hold operated indicator light illuminates when the brake hold system is operating (vehicle stopped via brake fluid pressure hold) and turns off when the brake hold system operation is finished (brake fluid pressure decreases).

The brake hold system may not operate depending on vehicle conditions even when the system is in standby mode and the brake hold standby indicator light is illuminated.

If there is a system malfunction that causes brake hold control to be prohibited, when the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operated indicator light blinks.

Vehicle Conditions:

(a)

The driver side door is closed.

(b)

The driver side seat belt is fastened.



HINT:
·

When the power switch is turned off during brake hold operation, control stops.

·

If brake hold control does not operate even when the vehicle stops, depress on the brake pedal again firmly to stop the vehicle.

If brake hold control still does not operate, confirm the conditions for brake hold control to operate.



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.PRE-CHECK

b.

If the brake hold operated indicator light does not illuminate although the brake hold standby indicator light is illuminated, check that the following brake hold operation (maintaining brake fluid pressure) conditions are met.

1.

System is in operation standby state (brake hold standby indicator light is illuminated).

2.

Shift position is not P or R.

3.

Driver is depressing brake pedal and vehicle is fully stopped.

4.

Driver is not depressing accelerator pedal.

5.

Vehicle is not on steep decline.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system

·

Hybrid control system




Result:
Proceed to
NEXT



NEXT

2.INSPECT COMBINATION METER ASSEMBLY
2.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Hold Indicator
50004 409 118

c.

Check the combination meter assembly.

OK:

The brake hold operated indicator light turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD OPERATED INDICATOR LIGHT)

NG

3.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD OPERATED INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Operated Light Brake hold operated indicator light Indicator light ON/OFF Observe combination meter assembly
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Operated Light Brake hold operated indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
BH Operated Light
Data List Display
BH Operated Light
50004 105 74 281

b.

Check the operating condition of the brake hold operated indicator light when operating it using the GTS.


Result:
Result Proceed to
Brake hold operated indicator light in the Data List does not change using the Active Test. A
Brake hold operated indicator light in the Data List turns ON/OFF using the Active Test. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B