Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0331186 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Power window regulator motor assembly (driver door)

·

Power window regulator motor assembly (front passenger door)

·

Power window regulator motor assembly (rear LH door)

·

Power window regulator motor assembly (rear RH door)

·

Sliding roof ECU (sliding roof drive gear sub-assembly)*1

·

Sliding roof ECU (sliding roof drive gear assembly)*2

·

Roof sunshade ECU (sliding roof drive gear assembly)*2

·

Wire harness or connector



*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System


WIRING DIAGRAM

B484141E04
3.104,5.281 3.26,5.479 0.156,0.198 10 false 7 3.104,3.604 3.26,3.802 0.156,0.198 10 false 7 2.781,3.781 3.396,3.979 0.615,0.198 10 false LIN 2.781,5.469 3.396,5.667 0.615,0.198 10 false LIN 1.417,4.208 1.729,4.406 0.313,0.198 10 false o1 1.417,4.365 3.333,5.156 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*4 1.302,6.094 3.417,6.885 2.115,0.792 10 false Roof Sunshade ECU (Sliding Roof Drive Gear Assembly)*4 1.313,5.917 1.625,6.115 0.313,0.198 10 false o2 4.521,8.969 6.26,9.573 1.74,0.604 10 false *3: w/ Sliding Roof System 4.531,9.375 6.917,9.833 2.385,0.458 10 false *4: w/ Panoramic Moon Roof System 2.688,0.177 3.302,0.375 0.615,0.198 10 false LIN2 2.688,0.615 3.302,0.813 0.615,0.198 10 false LIN1 3.073,0.052 3.385,0.25 0.313,0.198 10 false 16 3.083,0.458 3.396,0.656 0.313,0.198 10 false 17 1.438,0.917 2.417,1.188 0.979,0.271 10 false O2*1, N2*2 1.438,1.063 3.479,1.771 2.042,0.708 10 false Multiplex Network Master Switch Assembly 5.292,0.208 5.75,0.406 0.458,0.198 10 false LIN 5,0.927 6.021,1.125 1.021,0.198 10 false O6*1, N7*2 5.01,1.083 6.969,1.917 1.958,0.833 10 false Power Window Regulator Motor Assembly (Driver Door) 1.427,2.448 1.74,2.646 0.313,0.198 10 false V2 1.427,2.625 3.344,3.417 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)*3 4.979,3.031 6.948,3.865 1.969,0.833 10 false Power Window Regulator Motor Assembly (Front Passenger Door) 4.979,2.885 6.083,3.135 1.104,0.25 10 false N7*1, O6*2 5.292,2.354 5.75,2.552 0.458,0.198 10 false LIN 5.073,0.052 5.229,0.25 0.156,0.198 10 false 9 5.052,2.188 5.208,2.385 0.156,0.198 10 false 9 5,4.979 6.958,5.813 1.958,0.833 10 false Power Window Regulator Motor Assembly (Rear LH Door) 4.99,4.823 5.302,5.021 0.313,0.198 10 false Q6 4.948,6.917 6.906,7.75 1.958,0.833 10 false Power Window Regulator Motor Assembly (Rear RH Door) 4.948,6.781 5.26,6.979 0.313,0.198 10 false P6 5.302,4.313 5.76,4.51 0.458,0.198 10 false LIN 5.302,6.26 5.76,6.458 0.458,0.198 10 false LIN 5.063,4.156 5.219,4.354 0.156,0.198 10 false 9 5.063,6.104 5.219,6.302 0.156,0.198 10 false 9 2.615,2.073 3.229,2.271 0.615,0.198 10 false MPX1 3.104,1.917 3.26,2.115 0.156,0.198 10 false 7 3.115,6.948 3.427,7.146 0.313,0.198 10 false 17 3.125,7.354 3.438,7.552 0.313,0.198 10 false 25 3.167,7.719 3.323,7.917 0.156,0.198 10 false 3 3.115,7.146 3.427,7.344 0.313,0.198 10 false 3B 3.115,7.896 3.427,8.094 0.313,0.198 10 false 3B 3.115,7.531 3.427,7.729 0.313,0.198 10 false 3D 2.063,7 2.375,7.198 0.313,0.198 10 false 16 2.094,7.792 2.406,7.99 0.313,0.198 10 false 11 1.677,7.135 2.292,7.333 0.615,0.198 10 false LIN2 1.583,7.885 2.198,8.083 0.615,0.198 10 false GND1 0.448,8.344 0.76,8.542 0.313,0.198 10 false MB 0.448,8.5 2.104,9.208 1.656,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 2.24,8.26 3.854,9.146 1.615,0.885 10 false Instrument Panel Junction Block Assembly 0.396,9.458 4.063,9.656 3.667,0.198 10 false : LIN Communication Line 4.531,8.188 6.219,8.385 1.688,0.198 10 false *1: for LHD 4.531,8.573 6.219,8.771 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*1

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*2

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System



PROCEDURE

1.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
a.

Disconnect the O6*1 or N7*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the O2*1 or N*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

B

13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
a.

Disconnect the N7*1 or O6*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

4.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

4.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
a.

Disconnect the P6 power window regulator motor assembly (rear RH door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
a.

Disconnect the Q6 power window regulator motor assembly (rear LH door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/ Panoramic Moon Roof System) B
DTC B2325 is output (w/o Sliding Roof System and Panoramic Moon Roof System) C
DTC B2325 is not output D



A

6.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

7.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

D

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

6.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

7.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the o1 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

8.CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the o2 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

B

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - Body ground Always 10 kΩ or higher



c.

Disconnect all other connectors in the same circuit.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - Other terminals Always 10 kΩ or higher



Result:
Result Proceed to
OK (w/ Sliding Roof System or Panoramic Moon Roof System) A
OK (w/o Sliding Roof System and Panoramic Moon Roof System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

B

12.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-17 - Body ground Always 10 kΩ or higher
3B-17 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

B426691C08
5.646,1.375 6.063,1.625 0.417,0.25 5.646,0.125 6.063,0.375 0.417,0.25 1.958,1 2.375,1.25 0.417,0.25 2.167,2 2.167,1.573 false 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 2.073,1.052 2.385,1.25 0.313,0.198 10 false MB 5.771,1.427 6.083,1.625 0.313,0.198 10 false 3D 5.771,0.177 6.083,0.375 0.313,0.198 10 false 3B 2.052,2.031 2.365,2.229 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - 3B-3 Always 10 kΩ or higher
MB-16 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

12.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


b.

Connect all instrument panel junction block assembly connectors other than 3B and 3D.

B473136C01
1.729,0.083 2.146,0.333 0.417,0.25 1.75,1.344 2.167,1.594 0.417,0.25 3.938,2 4.344,2.208 0.406,0.208 10 false GND 0.167,0.125 0.573,0.333 0.406,0.208 10 false *a 3.927,0.167 4.333,0.375 0.406,0.208 10 false *b 1.854,0.135 2.188,0.344 0.333,0.208 10 false 3B 1.875,1.385 2.208,1.594 0.333,0.208 10 false 3D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Waveform 1



c.

Using a GTS, check the waveform.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).



OK:
Tester Connection Condition Tool Setting Specified Condition
3D-25 - Body ground Power switch on (IG) 2 V/DIV., 200 ms/DIV. Pulse generation
(See waveform 1)
3B-17 - Body ground* Power switch on (IG) 2 V/DIV., 200 ms/DIV. Pulse generation
(See waveform 1)


*: w/ Sliding Roof System or Panoramic Moon Roof System


Result:
Proceed to
OK
NG



OK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O2-16 (LIN2) - Body ground Always 10 kΩ or higher
O2-16 (LIN2) - Other terminals Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
N2-16 (LIN2) - Body ground Always 10 kΩ or higher
N2-16 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR