Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0AA073  Hybrid/EV Battery Positive and Negative Contactor Actuator Stuck Closed  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU assembly detects a stuck closed malfunction of a system main relay on the positive (+) terminal side and negative (-) terminal side of the HV battery.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

HV battery junction block assembly malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU assembly malfunction

·

HV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AE411

This circuit uses the hybrid vehicle control ECU assembly to monitor the system main relays and stops the system if a malfunction is detected in the relays, because it may be impossible to shut off the high-voltage system if any of the relays becomes stuck.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AA073 Hybrid/EV Battery Positive and Negative Contactor Actuator Stuck Closed Even both of the system main relays (HV battery positive (+) and negative (-) terminal side) are turned off, the inverter voltage (VH) does not drop.
(1 trip detection logic)
·

HV battery junction block assembly

·

Inverter with converter assembly

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0AA073
·

Hybrid Battery Voltage

·

VH-Voltage after Boosting

·

VL-Voltage before Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V, the vehicle has returned to normal.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY).

·

Do not turn the power switch on (IG) with the service plug grip removed, as this may cause a malfunction.

·

If DTC P0AA073 is output, do not install the service plug grip before completing repair.

If the service plug grip is not removed, the HV battery will gradually discharge and the SOC will decrease.



HINT:

If DTC P0AA073 is output, the power switch cannot be turned on (READY).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P0AA073 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety μC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P1C2B1C Drive Motor "A" Control Module A/D Converter Circuit Voltage Out of Range
P1C2B49 Drive Motor "A" Control Module A/D Converter Circuit Internal Electronic Failure
P1CAC49 Generator Position Sensor Internal Electronic Failure
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1CAF38 Generator Position Sensor REF Signal Cycle Malfunction Signal Frequency Incorrect
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
P06B01C Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
Motor generator control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A4B16 Generator Position Sensor Circuit Voltage Below Threshold
P0A4B21 Generator Position Sensor Signal Amplitude < Minimum
P0A4B22 Generator Position Sensor Signal Amplitude > Maximum
P0C5013 Drive Motor "A" Position Sensor Circuit "A" Circuit Open
P0C5016 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C5017 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C5A13 Drive Motor "A" Position Sensor Circuit "B" Circuit Open
P0C5A16 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C5A17 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Above Threshold
P0C6413 Generator Position Sensor Circuit "A" Circuit Open
P0C6416 Generator Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C6417 Generator Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C6913 Generator Position Sensor Circuit "B" Circuit Open
P0C6916 Generator Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C6917 Generator Position Sensor Circuit "B" Circuit Voltage Above Threshold
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor (VH) Stuck On

HINT:
·

P0AA073 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P0AA073.

Powertrain > Hybrid Control > Trouble Codes
50001 397
NOTICE:

As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").


Result:
Result Proceed to
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is less than 76 V. A
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is 76 V or more. B


HINT:

If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA073 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.



e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

4.CONNECT SECURELY
4.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

6.CONNECT SECURELY

C

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.
A405664N01
1.313,1.281 1.729,1.552 0.417,0.271 1.333,1.302 1.698,1.521 0.365,0.219 10 true R22

Check the connector connections and contact pressure of the relevant terminals of the R22 HV battery junction block assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



d.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

NG

9.CONNECT SECURELY
9.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

OK

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

11.CONNECT SECURELY
11.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the R22 HV battery junction block assembly connector.


d.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


e.
C361306C58
2.5,3.5 2.917,3.75 0.417,0.25 1.833,0.167 2.25,0.417 0.417,0.25 0.948,4.188 1.365,3.771 true 2.417,2.396 2.104,1.823 true 1.719,4.188 1.604,3.792 true 2.385,4.198 2.01,3.781 true 2.833,2.385 2.25,1.833 true 1.646,2.396 2.031,1.823 true 0.167,0.083 0.479,0.24 0.313,0.156 10 false *a 0.188,2.917 0.5,3.073 0.313,0.156 10 false *b 1.927,0.219 2.385,0.417 0.458,0.198 10 false K69 2.604,3.552 3.063,3.75 0.458,0.198 10 false R22 0.719,4.219 1.333,4.417 0.615,0.198 10 false SMRB 1.469,2.448 2.083,2.646 0.615,0.198 10 false SMRB 1.552,4.219 2.167,4.417 0.615,0.198 10 false SMRP 2.25,4.219 2.865,4.417 0.615,0.198 10 false SMRG 2.771,2.417 3.385,2.615 0.615,0.198 10 false SMRG 2.281,2.448 2.896,2.646 0.615,0.198 10 false SMRP
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
K69-4 (SMRB) - R22-1 (SMRB) Power switch off Below 1 Ω
K69-1 (SMRG) - R22-4 (SMRG) Power switch off Below 1 Ω
K69-3 (SMRP) - R22-2 (SMRP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
K69-4 (SMRB) or R22-1 (SMRB) - Body ground and other terminals Power switch off 10 kΩ or higher
K69-1 (SMRG) or R22-4 (SMRG) - Body ground and other terminals Power switch off 10 kΩ or higher
K69-3 (SMRP) or R22-2 (SMRP) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the K69 hybrid vehicle control ECU assembly connector.


g.

Reconnect the R22 HV battery junction block assembly connector.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

14.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
14.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the R22 HV battery junction block assembly connector.


d.
A365602C26
2.656,1.083 3.01,1.344 0.354,0.26 1.896,1.25 2.292,1.823 false 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 2.719,1.125 3.031,1.281 0.313,0.156 10 false R22
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R22-3 (GND) - Body ground Power switch off Below 1 Ω



e.

Reconnect the R22 HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

16.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB, SMRG, SMRP)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

16.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB, SMRG, SMRP)
16.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB, SMRG, SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the R22 HV battery junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

A407179C30
3.76,0.969 4.115,1.177 0.354,0.208 3.292,1.365 3.385,1.188 true 4.083,1.354 3.625,1.177 true 3.646,1.365 3.51,1.188 true 2.833,1.396 3.271,1.188 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.833,1 4.292,1.198 0.458,0.198 10 false R22 3.135,1.396 3.448,1.604 0.313,0.208 10 true GND 3.958,1.385 4.479,1.594 0.521,0.208 10 true SMRB 3.5,1.385 3.917,1.615 0.417,0.229 10 true SMRP 2.635,1.396 3.083,1.635 0.448,0.24 10 true SMRG
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
R22-1 (SMRB) - R22-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω
R22-4 (SMRG) - R22-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω
R22-2 (SMRP) - R22-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω



e.

Reconnect the R22 HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

17.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB, SMRG, SMRP)

NG

19.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY
17.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB, SMRG, SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.
A405691

Disconnect the 2 HV floor under wire connectors from the HV battery junction block assembly.


d.

Disconnect the 2 HV battery high voltage connectors from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



e.
A405692C03
1.031,0.417 1.396,0.656 0.365,0.24 1.76,0.906 2.125,1.146 0.365,0.24 0.427,1.073 0.781,0.854 true 1.521,1.583 1.698,1.344 true 0.156,0.156 0.438,0.375 0.281,0.219 10 true *a 1.052,0.438 1.365,0.635 0.313,0.198 10 true z25 0.302,1.083 0.458,1.281 0.156,0.198 10 true + 1.792,0.927 2.104,1.125 0.313,0.198 10 true s2 1.385,1.635 1.667,1.833 0.281,0.198 10 true CBI
*a Component without harness connected
(HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s2-1 (CBI) - z25-1 (+) Power switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the HV battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the HV battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.




f.
A405692C02
2.625,1.417 2.99,1.656 0.365,0.24 1.99,1.104 2.354,1.344 0.365,0.24 2.583,2.021 2.458,1.729 true 1.771,1.729 2.052,1.5 true 0.156,0.156 0.438,0.375 0.281,0.219 10 true *a 2.656,1.427 2.969,1.625 0.313,0.198 10 true z20 2.625,1.927 2.781,2.125 0.156,0.198 10 true - 2.01,1.125 2.323,1.323 0.313,0.198 10 true s3 1.604,1.76 1.885,1.958 0.281,0.198 10 true CEI
*a Component without harness connected
(HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s3-1 (CEI) - z20-1 (-) Power switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the HV battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the HV battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.

·

If the resistance is between 24.3 and 29.7 Ω, it can be determined that SMRP is stuck closed.




g.

Reconnect the 2 HV battery high voltage connectors.


h.

Reconnect the 2 HV floor under wire connectors.


i.

Install the No. 1 HV battery cover panel RH.


Result:
Result Judgment Proceed to
OK Past malfunction A
NG Present malfunction B



A

18.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

B

20.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY
18.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

21.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)
19.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

21.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)
20.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

21.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)
21.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V. A
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is 100 V or more. B



A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY AND HV BATTERY JUNCTION BLOCK ASSEMBLY