Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.12–2018.04
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150718  Turn Signal Light Circuit Current Below Threshold  


DESCRIPTION

This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.

HINT:
·

If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.

·

If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.



DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150718 Turn Signal Light Circuit Current Below Threshold Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:
·

Open in front turn signal light circuit

·

Open in rear turn signal light circuit


·

Headlight ECU sub-assembly

·

Head light unit assembly

·

Headlight lens*1

·

Rear combination light assembly*2

·

Rear combination light cord*2

·

Rear combination light socket and wire*3

·

Harness or connector

·

Combination meter assembly


DTC stored -

*1: for LED Type Turn Signal Light

*2: for LED Type Back-up Light

*3: for Bulb Type Back-up Light


WIRING DIAGRAM

LH side


E376454E01
5.625,0.427 5.938,0.625 0.313,0.198 10 false LL 1.552,1.76 4.219,2.115 2.667,0.354 10 false Headlight ECU Sub-assembly LH 1.458,2.479 4.125,2.833 2.667,0.354 10 false Headlight Assembly LH 0.427,3.938 3.094,4.292 2.667,0.354 10 false Headlight Lens LH 1.479,5.26 4.146,5.615 2.667,0.354 10 false Headlight Assembly LH 1.542,4.573 4.208,4.927 2.667,0.354 10 false Headlight ECU Sub-assembly LH 0.281,1.635 1.146,2.021 0.865,0.385 10 false Headlight Unit Assembly LH 0.292,4.417 1.156,4.802 0.865,0.385 10 false Headlight Unit Assembly LH 1.021,6.563 3.688,6.917 2.667,0.354 10 false Rear Combination Light Cord LH 0.698,7.031 3.365,7.385 2.667,0.354 10 false Rear Combination Light Assembly LH 0.74,8.813 3.406,9.167 2.667,0.354 10 false Rear Combination Light Assembly LH 0.375,8.323 3.781,8.625 3.406,0.302 10 false Rear Combination Light Socket and Wire LH 1.115,2.49 1.688,2.74 0.573,0.25 10 false A10 1.552,1.594 1.833,1.833 0.281,0.24 10 false B 2.219,0.417 3.125,0.615 0.906,0.198 10 false TURN+ 2.219,0.771 3.125,0.969 0.906,0.198 10 false TURN- 3.333,0.427 4.24,0.625 0.906,0.198 10 false TNS 3.323,0.771 4.229,0.969 0.906,0.198 10 false GND 1.542,4.406 1.823,4.646 0.281,0.24 10 false B 5.604,5.844 6.365,6.115 0.76,0.271 10 false TRNL 6.177,3.5 6.844,3.823 0.667,0.323 10 false FLASHER IC 1.125,5.26 1.698,5.51 0.573,0.25 10 false A10 0.323,7.031 0.896,7.281 0.573,0.25 10 false W13 0.375,8.813 0.948,9.063 0.573,0.25 10 false W13 2.229,3.219 3.135,3.417 0.906,0.198 10 false TURN+ 2.229,3.563 3.135,3.76 0.906,0.198 10 false TURN- 3.323,3.573 4.229,3.771 0.906,0.198 10 false GND 3.354,3.219 4.26,3.417 0.906,0.198 10 false TNS 5.865,7.5 7.042,7.896 1.177,0.396 10 false Combination Meter Assembly 5.531,7.51 6.292,7.781 0.76,0.271 10 false K20 2.615,9.156 5.281,9.51 2.667,0.354 10 false *1: for LED Type Turn Signal Light 4.865,9.156 7.01,9.49 2.146,0.333 10 false *2: for Bulb Type Turn Signal Light 2.615,9.479 5.281,9.833 2.667,0.354 10 false *3: for LED Type Back-up Light 4.875,9.49 6.781,9.802 1.906,0.313 10 false *4: for Bulb Type Back-up Light 3,5.854 3.76,6.125 0.76,0.271 10 false B 2.99,7.625 3.75,7.896 0.76,0.271 10 false B 2.99,7.969 3.75,8.24 0.76,0.271 10 false E 2.99,6.198 3.24,6.469 0.25,0.271 10 false E 3.719,0.427 4.031,0.625 0.313,0.198 10 false 11 3.729,0.771 4.042,0.969 0.313,0.198 10 false 12 3.719,3.573 4.031,3.771 0.313,0.198 10 false 12 3.719,3.219 4.031,3.417 0.313,0.198 10 false 11 3.24,5.854 3.552,6.052 0.313,0.198 10 false 3 3.219,7.625 3.531,7.823 0.313,0.198 10 false 3 3.219,7.969 3.531,8.167 0.313,0.198 10 false 4 3.24,6.198 3.552,6.396 0.313,0.198 10 false 4 5.354,0.427 5.667,0.625 0.313,0.198 10 false 11 5.323,5.844 6.083,6.115 0.76,0.271 10 false 10 4.948,3.198 5.26,3.396 0.313,0.198 10 false *1 4.948,0.427 5.26,0.625 0.313,0.198 10 false *2 4.958,5.844 5.271,6.042 0.313,0.198 10 false *3 4.969,7.615 5.281,7.813 0.313,0.198 10 false *4 2.01,0.417 2.323,0.615 0.313,0.198 10 false 9 1.958,0.771 2.271,0.969 0.313,0.198 10 false 13 1.969,3.583 2.281,3.781 0.313,0.198 10 false 13 2.01,3.219 2.323,3.417 0.313,0.198 10 false 9


RH side


E376454E03
5.625,0.427 5.938,0.625 0.313,0.198 10 false LR 1.542,1.75 4.208,2.104 2.667,0.354 10 false Headlight ECU Sub-assembly RH 1.458,2.479 4.125,2.833 2.667,0.354 10 false Headlight Assembly RH 0.427,3.938 3.094,4.292 2.667,0.354 10 false Headlight Lens RH 1.479,5.26 4.146,5.615 2.667,0.354 10 false Headlight Assembly RH 1.521,4.563 4.188,4.917 2.667,0.354 10 false Headlight ECU Sub-assembly RH 0.281,1.635 1.146,2.021 0.865,0.385 10 false Headlight Unit Assembly RH 0.292,4.417 1.156,4.802 0.865,0.385 10 false Headlight Unit Assembly RH 1.021,6.563 3.688,6.917 2.667,0.354 10 false Rear Combination Light Cord RH 0.698,7.031 3.365,7.385 2.667,0.354 10 false Rear Combination Light Assembly RH 0.74,8.823 3.406,9.177 2.667,0.354 10 false Rear Combination Light Assembly RH 0.292,8.323 3.698,8.625 3.406,0.302 10 false Rear Combination Light Socket and Wire RH 1.115,2.49 1.688,2.74 0.573,0.25 10 false A11 1.552,1.594 1.833,1.833 0.281,0.24 10 false B 2.219,0.417 3.125,0.615 0.906,0.198 10 false TURN+ 2.219,0.771 3.125,0.969 0.906,0.198 10 false TURN- 3.333,0.427 4.24,0.625 0.906,0.198 10 false TNS 3.323,0.771 4.229,0.969 0.906,0.198 10 false GND 1.542,4.406 1.823,4.646 0.281,0.24 10 false B 5.604,5.833 6.365,6.104 0.76,0.271 10 false TRNR 6.177,3.5 6.844,3.823 0.667,0.323 10 false FLASHER IC 1.125,5.26 1.698,5.51 0.573,0.25 10 false A11 0.323,7.031 0.896,7.281 0.573,0.25 10 false W12 0.375,8.813 0.948,9.063 0.573,0.25 10 false W12 2.229,3.219 3.135,3.417 0.906,0.198 10 false TURN+ 2.229,3.563 3.135,3.76 0.906,0.198 10 false TURN- 3.323,3.573 4.229,3.771 0.906,0.198 10 false GND 3.354,3.219 4.26,3.417 0.906,0.198 10 false TNS 5.865,7.5 7.042,7.896 1.177,0.396 10 false Combination Meter Assembly 5.531,7.51 6.292,7.781 0.76,0.271 10 false K20 2.708,9.156 5.375,9.51 2.667,0.354 10 false *1: for LED Type Turn Signal Light 4.958,9.156 7.094,9.417 2.135,0.26 10 false *2: for Bulb Type Turn Signal Light 2.708,9.479 5.375,9.833 2.667,0.354 10 false *3: for LED Type Back-up Light 4.958,9.479 6.865,9.792 1.906,0.313 10 false *4: for Bulb Type Back-up Light 3,5.854 3.76,6.125 0.76,0.271 10 false B 2.99,7.625 3.75,7.896 0.76,0.271 10 false B 2.99,7.979 3.75,8.25 0.76,0.271 10 false E 2.99,6.198 3.24,6.469 0.25,0.271 10 false E 3.719,0.427 4.031,0.625 0.313,0.198 10 false 11 3.729,0.771 4.042,0.969 0.313,0.198 10 false 12 3.719,3.573 4.031,3.771 0.313,0.198 10 false 12 3.719,3.219 4.031,3.417 0.313,0.198 10 false 11 3.24,5.854 3.552,6.052 0.313,0.198 10 false 3 3.219,7.625 3.531,7.823 0.313,0.198 10 false 3 3.219,7.979 3.531,8.177 0.313,0.198 10 false 4 3.24,6.198 3.552,6.396 0.313,0.198 10 false 4 5.344,0.427 5.656,0.625 0.313,0.198 10 false 7 5.323,5.833 6.083,6.104 0.76,0.271 10 false 13 4.948,3.198 5.26,3.396 0.313,0.198 10 false *1 4.948,0.427 5.26,0.625 0.313,0.198 10 false *2 4.958,5.833 5.271,6.031 0.313,0.198 10 false *3 4.969,7.615 5.281,7.813 0.313,0.198 10 false *4 2.021,0.417 2.333,0.615 0.313,0.198 10 false 9 1.958,0.771 2.271,0.969 0.313,0.198 10 false 13 1.969,3.552 2.281,3.75 0.313,0.198 10 false 13 2.021,3.219 2.333,3.417 0.313,0.198 10 false 9


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the turn signal light bulbs and sockets before performing the following procedure.



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH does not blink A
Rear turn signal light LH does not blink B
Front turn signal light RH does not blink C
Rear turn signal light RH does not blink D



A

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

D

17.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A10 headlight assembly LH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-11 (TNS) - K20-11 (LL) Always Below 1 Ω
A10-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
E334043C09
2.156,0.219 2.458,0.427 0.302,0.208 5.604,0.323 5.906,0.531 0.302,0.208 1.219,0.302 1.646,0.813 true 3.146,0.865 3.458,0.323 true 5.323,0.979 5.083,0.385 true 6.052,1.104 6.448,0.385 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 2.188,0.229 2.5,0.427 0.313,0.198 10 false A10 5.708,0.333 6.021,0.531 0.313,0.198 10 false B 1.073,0.115 1.385,0.313 0.313,0.198 10 false TNS 3.354,0.146 3.667,0.344 0.313,0.198 10 false GND 4.875,0.198 5.406,0.417 0.531,0.219 10 false TURN+ 6.271,0.198 6.823,0.417 0.552,0.219 10 false TURN-
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
- -


a.

Remove the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - A10-11 (TNS) Always Below 1 Ω
B-13 (TURN-) - A10-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HEADLIGHT UNIT ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

4.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Remove each headlight ECU sub-assembly, interchange the headlight unit assembly LH with RH and connect the connectors.

for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY

for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY


b.

Check that the front turn signal light operates normally.

OK:

Front turn signal light blinks.



Result:
Proceed to
OK
NG



OK

5.CONFIRM MODEL

NG

REPLACE COMBINATION METER ASSEMBLY

5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Turn Signal Light A
for Bulb Type Turn Signal Light B



A

6.INSPECT HEADLIGHT LENS LH

B

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the W13 rear combination light assembly LH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W13-3 (B) - K20-10 (TRNL) Always Below 1 Ω
W13-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Back-up Light A
for Bulb Type Back-up Light B



A

9.CHECK REAR COMBINATION LIGHT CORD LH

B

11.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE LH
9.CHECK REAR COMBINATION LIGHT CORD LH
a.

Interchange the rear combination light cord LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT CORD LH

NG

10.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH
10.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH
a.

Remove the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL


b.

Inspect the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

11.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE LH
a.

Interchange the rear combination light socket and wire LH with RH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE LH

NG

REPLACE COMBINATION METER ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A11 headlight assembly RH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-11 (TNS) - K20-7 (LR) Always Below 1 Ω
A11-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
E334043C10
2.156,0.219 2.458,0.427 0.302,0.208 5.604,0.323 5.906,0.531 0.302,0.208 1.219,0.302 1.646,0.813 true 3.146,0.865 3.458,0.323 true 5.323,0.979 5.083,0.385 true 6.052,1.104 6.448,0.385 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 2.198,0.25 2.51,0.448 0.313,0.198 10 false A11 5.719,0.344 6.031,0.542 0.313,0.198 10 false B 1.073,0.115 1.385,0.313 0.313,0.198 10 false TNS 3.354,0.135 3.667,0.333 0.313,0.198 10 false GND 4.875,0.188 5.417,0.396 0.542,0.208 10 false TURN+ 6.25,0.198 6.729,0.448 0.479,0.25 10 false TURN-
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


a.

Remove the headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 (TURN+) - A11-11 (TNS) Always Below 1 Ω
B-13 (TURN-) - A11-12 (GND) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

14.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Remove each headlight ECU sub-assembly, interchange the headlight unit assembly RH with LH and connect the connectors.

for LED Type Turn Signal: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY

for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY


b.

Check that the front turn signal light operates normally.

OK:

Front turn signal light blinks.



Result:
Proceed to
OK
NG



OK

15.CONFIRM MODEL

NG

REPLACE COMBINATION METER ASSEMBLY

15.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Turn Signal Light A
for Bulb Type Turn Signal Light B



A

16.INSPECT HEADLIGHT LENS RH

B

17.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the W12 rear combination light assembly RH connector.


b.

Disconnect the K20 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W12-3 (B) - K20-13 (TRNR) Always Below 1 Ω
W12-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LED Type Back-up Light A
for Bulb Type Back-up Light B



A

19.CHECK REAR COMBINATION LIGHT CORD RH

B

21.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE RH
19.CHECK REAR COMBINATION LIGHT CORD RH
a.

Interchange the rear combination light cord RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT CORD RH

NG

20.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH
20.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH
a.

Remove the rear combination light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL


b.

Inspect the rear combination light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

21.CHECK REAR COMBINATION LIGHT SOCKET AND WIRE RH
a.

Interchange the rear combination light socket and wire RH with LH and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the rear turn signal light operates normally.

OK:

Rear turn signal light blinks.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE RH

NG

REPLACE COMBINATION METER ASSEMBLY