This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.
If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status: Short in turn signal light circuit |
·
Headlight ECU sub-assembly ·
Head light unit assembly ·
Headlight lens*1 ·
Side turn signal light assembly ·
Outer rear view mirror assembly*4 ·
Outer mirror retractor*5 ·
Rear combination light assembly*2 ·
Rear combination light cord*2 ·
Rear combination light socket and wire*3 ·
Harness or connector ·
Combination meter assembly |
DTC stored | - |
*1: for LED Type Turn Signal Light
*2: for LED Type Back-up Light
*3: for Bulb Type Back-up Light
*4: w/ Seat Position Memory System
*5: w/o Seat Position Memory System
LH side
RH side
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs and sockets before performing the following procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| All LH turn signal lights do not blink | A |
| All RH turn signal lights do not blink | B |
A
B
Disconnect the A10 headlight assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the headlight turn signal light blink.
If the LH side turn signal lights blink, the headlight assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
| *a | Component without harness connected
(Headlight ECU Sub-assembly LH) |
- | - |
Remove the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - B-13 (TURN-)
or A10-11 (TNS) - A10-12 (GND) |
Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Connect the A10 headlight assembly LH connector.
Disconnect the O16 outer rear view mirror assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights blink, the outer rear view mirror assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Connect the O16 outer rear view mirror assembly LH connector.
Disconnect the W13 rear combination light assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights blink, the rear combination light assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Remove the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W13-3 (B) or K20-10 (TRNL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A10 headlight assembly LH connector.
Disconnect the O16 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A10-11 (TNS), O16-10 (B) or K20-11 (LL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A11 headlight assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the headlight turn signal light blink.
If the RH side turn signal lights blink, the headlight assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
| *a | Component without harness connected
(Headlight ECU Sub-assembly RH) |
- | - |
Remove the headlight ECU sub-assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - B-13 (TURN-)
or A11-11 (TNS) - A11-12 (GND) |
Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Connect the A11 headlight assembly RH connector.
Disconnect the N19 outer rear view mirror assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights blink, the outer rear view mirror assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Connect the N19 outer rear view mirror assembly RH connector.
Disconnect the W12 rear combination light assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights blink, the rear combination light assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Remove the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W12-3 (B) or K20-13 (TRNR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A11 headlight assembly RH connector.
Disconnect the N19 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A11-11 (TNS), N19-10 (B) or K20-7 (LR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG