Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2018.04–2019.02
RM33C0E _58 Vehicle Interior _065466 INTERIOR PANELS / TRIM _0328285 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 2.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 3.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 4.REMOVE REAR SEAT ASSEMBLY (for Reclining Seat Type)

Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B468865C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.

HINT:

Use the same procedure for the front side and rear side.



b.
B468866C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 8 claws and guide to remove the front door scuff plate LH as shown in the illustration.


Hide 62112A 6.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

a.
B468867C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.


Hide 62312B 7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62212 8.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.
B468868C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front pillar garnish LH as shown in the illustration.


b.
B502767C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Pull the upper part of the front pillar garnish LH as shown in the illustration to disengage the 2 clips.


c.
B468873C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.


Hide 62212 9.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.
B468868C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front pillar garnish LH as shown in the illustration.


b.
B468869C01
2.844,1.906 2.844,1.76 true 2.76,1.927 3.073,2.083 0.313,0.156 10 false *1
*1 Front Pillar Garnish Clip
V113146

Place Hand Here
V113147

Remove in this Direction


Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.



c.
B468870C01
2.448,0.99 2.448,0.719 true 2.365,1.01 2.677,1.167 0.313,0.156 10 false *1
*1 Front Pillar Garnish Clip
V113147

Remove in this Direction


While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

NOTICE:
·

The front pillar garnish clip is reusable if it is not damaged.

·

If the front pillar garnish clip is damaged, replace it with a new one.



HINT:

When the front pillar garnish clip cannot be disengaged easily:

1.
B468871C01
0,0 0,0 false
V113147

Move in this Direction


While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

2.
B468872C01
0,0 0,0 false
V113147

Pull in this Direction


While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.




d.
B468873C01
0,0 0,0 false
V113147

Remove in this Direction


w/o Front No. 3 Speaker:

i.

Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.



e.

w/ Front No. 3 Speaker:

i.

Disengage the 2 guides as shown in the illustration.


ii.

Disconnect the connector to remove the front pillar garnish LH.



f.

Remove the clip from the front pillar garnish LH.


g.
B484977C01
1.896,2.76 2,3.177 2,3.177 2.229,2.563 true 2.292,1.854 2.292,1.469 true 3.208,0.188 3.042,0.448 true 1.073,2.635 1.073,2.25 true 2.844,1.938 2.708,1.302 true 1.563,2.885 1.563,2.344 true 3.146,1.667 3.052,1.313 true 0.99,2.667 1.302,2.823 0.313,0.156 10 false *1 1.49,2.906 1.802,3.063 0.313,0.156 10 false *a 1.938,3.188 2.25,3.344 0.313,0.156 10 false *b 2.219,1.865 2.438,2.031 0.219,0.167 10 true *b 3.198,0.083 3.417,0.24 0.219,0.156 10 false *b 2.771,1.958 2.969,2.125 0.198,0.167 10 true *1 3.073,1.667 3.281,1.833 0.208,0.167 10 true *a
*1 Curtain Shield Airbag Assembly LH
*a Protective Cover
*b Adhesive Tape


Protect the curtain shield airbag assembly LH.

i.

Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.




Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

a.
B481810C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw as shown in the illustration.


b.
B481811C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 5 claws, clip and guide to remove the rear door scuff plate LH as shown in the illustration.


Hide 62332A 11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 73233 12.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 73220 13.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 14.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B468877C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 claws as shown in the illustration.


b.
B468878C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.


Hide 62412B 15.REMOVE UPPER CENTER PILLAR GARNISH LH

a.
B468879

Using a clip remover, remove the 2 clips.


b.
B468880C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


c.
B468881C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the clip and 2 guides to remove the upper center pillar garnish LH as shown in the illustration.


d.

w/ Curtain Shield Airbag:

1.

Remove the clip from the upper center pillar garnish LH.



Hide 62472A 16.REMOVE INNER ROOF SIDE GARNISH LH

a.
B468882C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips as shown in the illustration.


b.
B468883C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the inner roof side garnish LH as shown in the illustration.


c.

w/ Curtain Shield Airbag:

1.

Remove the 3 clips from the inner roof side garnish LH.



Hide 67913 17.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111A 18.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 19.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 20.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 62211 21.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 67917A 22.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62331A 23.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 24.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 73210 25.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 26.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62411B 27.REMOVE UPPER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62471A 28.REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 29.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 30.REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

Hide 31.REMOVE ROOF CONSOLE BOX ASSEMBLY

Hide 81240J 32.REMOVE ROOM LIGHT ASSEMBLY (for Bulb Type)

Hide 81360T 33.REMOVE SPOT LIGHT ASSEMBLY (for LED Type)

Hide 89943 34.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 87834 35.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

Hide 86466E 36.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 86466D 37.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 74610A 38.REMOVE ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for all assist grip assemblies.


a.
B484928C01
2.135,0.573 2.438,0.573 true 2.365,3.167 2.656,3.167 true 2.458,0.479 2.688,0.625 0.229,0.146 10 true *a 2.688,3.094 3.031,3.26 0.344,0.167 10 true SST
*a Cutout


Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

SST
09813-00010  

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.


HINT:

Use the same procedure for the LH side and RH side.



b.
B484929C01
2.604,1.448 2.823,1.448 true 2.042,1.979 2.354,2.135 0.313,0.156 10 false *a 2.865,1.365 3.208,1.542 0.344,0.177 10 true SST
*a 30 to 45°
V113147

Remove in this Direction


Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.


HINT:
·

Use the same procedure for the claw on the other side of the assist grip cover LH.

·

Use the same procedure for the LH side and RH side.




c.

Remove the assist grip cover LH.

HINT:

Use the same procedure for the LH side and RH side.



d.
B468888C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.


e.

Remove the 2 clips from the vehicle body.


Hide 74630E 39.REMOVE REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 74620C 40.REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip assembly.


Hide 74318 41.REMOVE VISOR BRACKET COVER LH

a.
B468889C01
0,0 0,0 false
V113146

Insert Moulding Remover Here


Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover LH.


Hide 74320 42.REMOVE VISOR ASSEMBLY LH

a.

for "TORX" Screw:

i.
B468890

Using a T25 "TORX" socket wrench, remove the 2 screws.



b.

except "TORX" Screw:

i.

Remove the 2 screws.



c.
B468891C01
1.75,0.635 2.135,0.74 true 1.521,0.531 1.729,0.719 0.208,0.188 10 true *1
*1 Visor Holder LH
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.


d.

Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.


Hide 74348C 43.REMOVE VISOR HOLDER LH

a.
B433794C02
1.563,0.125 1.781,0.333 0.219,0.208 10 true *a
*a 45°
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder LH approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.


b.

Disengage the 2 claws to remove the base of the visor holder LH.


Hide 74317 44.REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 74310 45.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348B 46.REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 63318C 47.REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof)

a.

Remove the sun roof opening trim moulding.


Hide 48.REMOVE ROOF HEADLINING ASSEMBLY

a.

for Windshield Glass Side:

i.

w/ EC Mirror or Pre-collision System:

1.

Disconnect each connector.




b.

for Front Pillar LH Side:

i.

Remove the protective cover.


ii.
B468892

Disconnect each connector.


iii.

Using a clip remover, disengage the 4 clamps.


iv.

Install the protective cover.



c.

for Front Pillar RH Side:

i.

Remove the protective cover.


ii.
B468893C01
0.26,1.167 0.26,0.771 true 2.5,0.854 2.5,1.5 2.5,1.5 1.844,1.188 true 0.188,1.177 0.438,1.365 0.25,0.188 10 true *a 2.427,1.531 2.74,1.688 0.313,0.156 10 false *b
*a Guide
*b Clamp


Remove the bolt.


iii.

Disengage the guide to disconnect the connector bracket.


iv.

Using a clip remover, disengage the 2 clamps.


v.

Install the protective cover.



d.

for Rear Pillar LH Side:

i.
B468894

Disconnect the connector.


ii.

Using a clip remover, disengage the clamp.



e.

for Rear Pillar RH Side:

i.
B468895C03
1.375,1.698 1.656,1.927 0.281,0.229 12 true *A 2.75,1.823 3.031,2.052 0.281,0.229 12 true *A
*A w/ Digital Audio Broadcasting Antenna


Disconnect each connector.


ii.

Using a clip remover, disengage each clamp.



f.

for Roof Side (for Normal Roof):

i.

Using a clip remover, remove the 2 clips.

B481812C01
0,0 0,0 false
V113147

Remove in this Direction - -



ii.

Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips installed to the vehicle body.




g.

for Roof Side (for Moon Roof):

i.

Using a clip remover, remove the 2 clips.

B481813C01
0,0 0,0 false
V113147

Remove in this Direction - -



ii.

Disconnect the connector.


iii.

Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips installed to the vehicle body.




h.

for Roof Side (for Panoramic Moon Roof):

i.

Using a clip remover, remove the 2 clips.

B481814C01
2.573,0.792 2.781,0.958 true 3.292,1.292 3.615,1.552 3.615,1.552 3.635,1.188 true 3.917,1.104 4.156,1.458 4.156,1.458 4.219,1.031 true 2.667,1.156 2.667,1.625 true 2.833,0.75 3.198,0.875 3.198,0.875 3.125,0.656 true 4.448,0.948 4.448,1.427 true 4.021,0.708 3.854,0.844 3.854,0.844 4.188,0.813 true 3.833,0.469 4.229,0.26 4.229,0.26 4.021,0.583 true 3.208,0.573 2.938,0.302 2.938,0.302 3.49,0.5 true 2.792,0.865 3,1.052 0.208,0.188 10 true *a 2.594,1.625 2.781,1.802 0.188,0.177 10 true *b 2.781,0.177 2.99,0.365 0.208,0.188 10 false *a 3.531,1.563 3.74,1.75 0.208,0.188 10 true *a 4.052,1.438 4.26,1.625 0.208,0.188 10 true *a 3.125,0.896 3.333,1.083 0.208,0.188 10 true *a 4.365,1.438 4.573,1.625 0.208,0.188 10 true *a 3.635,0.75 3.844,0.938 0.208,0.188 10 true *a 4.25,0.115 4.458,0.302 0.208,0.188 10 true *a
*a Fastener *b Guide
V113147

Remove in this Direction - -



ii.

Disconnect the connector.


iii.

Disengage the 14 fasteners and guide.


iv.

Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips installed to the vehicle body.




i.

Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.

B484984C01
0,0 0,0 false
V113147

Remove in this Direction - -


NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



j.
B468899C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 clips from the vehicle body as shown in the illustration.