Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › from 2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333603 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 72497B 1.INSTALL VERTICAL ADJUSTER BRACKET COVER (w/ Vertical Adjuster)

a.
B447560

Engage the claw to install the vertical adjuster bracket cover to the front vertical adjuster brake sub-assembly.


Hide 72031 2.INSTALL FRONT SEAT VERTICAL ADJUSTER ASSEMBLY (w/ Vertical Adjuster)

a.

Install the front seat vertical adjuster assembly.

i.
B489768C01
1.833,0.531 2.333,0.531 true 1.917,0.833 2.417,0.833 true 2.365,0.438 2.677,0.594 0.313,0.156 10 true *a 2.458,0.76 2.771,0.917 0.313,0.156 10 true *b
*a Stud Bolt of the Front Vertical Adjuster Brake Sub-assembly
*b Hole of the Front Seat Adjuster Assembly


Install the front vertical adjuster brake sub-assembly.

NOTICE:

Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.



ii.
B489766

Install the vertical adjuster spacer.


iii.
B489765N01
2.656,0.667 2.813,0.865 0.156,0.198 10 true 1 0.927,0.823 1.083,1.021 0.156,0.198 10 true 2 2.677,1.333 2.833,1.531 0.156,0.198 10 true 3

Install the vertical adjuster plate with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.




Hide 72211 3.INSTALL SEAT TRACK ADJUSTING HANDLE

a.
B489764

Engage the 2 claws to install the seat track adjusting handle to the front seat adjuster assembly.


Hide 71051A 4.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY

a.
B489763

Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.


Hide 7181A 5.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER

a.
B489762

Engage the claw to install the front seat cushion wire harness holder.


b.

Install the 2 screws.


Hide 82191 6.INSTALL FRONT SEAT WIRE RH (w/ Lumbar Support)

a.

Connect each connector and engage each clamp to install the front seat wire RH.


Hide 82191A 7.INSTALL FRONT SEAT WIRE RH (w/ Occupant Classification System)

a.

Connect each connector and engage each clamp to install the front seat wire RH.


Hide 82191 8.INSTALL FRONT SEAT WIRE (w/ Seat Heater System)

a.

Connect each connector and engage each clamp to install the front seat wire.


Hide 87501A 9.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

Hide 71874 10.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)

a.
B489761C01
2.573,0.552 2.99,0.552 true 1.99,1.354 2.99,1.354 true 2.99,0.458 3.302,0.615 0.313,0.156 10 true *a 3.021,1.271 3.333,1.427 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the claw and guide to install the front seat lower cushion shield LH.


b.

Engage the hook.


Hide 71873 11.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)

a.
B489760C01
2.49,0.615 2.99,0.615 true 2.073,1.594 2.99,1.594 true 3.021,0.531 3.333,0.688 0.313,0.156 10 false *a 3.031,1.521 3.344,1.677 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the claw and guide to install the front seat lower cushion shield RH.


b.

Engage the hook.


Hide 71875G 12.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Vertical Adjuster)

a.
B439759

Engage the 4 claws to install the LH seat reclining adjuster inside cover LH.


b.

w/ Lumbar Support:

i.
B491296

Engage the claw.



Hide 71876G 13.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH (w/ Vertical Adjuster)

a.
B491284

Engage the 4 claws to install the LH seat reclining adjuster inside cover RH.


Hide 71875F 14.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH (w/o Vertical Adjuster)

a.
B431139

Engage the 4 claws to install the RH seat reclining adjuster inside cover LH.


Hide 71876F 15.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH (w/o Vertical Adjuster)

a.
B431140

Engage the 4 claws to install the RH seat reclining adjuster inside cover RH.


Hide 87510K 16.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)

Hide 71071S 17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.
B471093

Engage the 14 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.


Hide 18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Engage the 10 hooks to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.

B439687


b.
B439686

Engage the 2 hooks.


c.

w/ Seat Heater System:

i.
B491322

Connect the connector and engage the clamp.



d.

w/ Occupant Detection Sensor:

i.
B477939C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the connector holder to the occupant detection sensor wire harness as shown in the illustration.


ii.
B477937C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the connector holder as shown in the illustration.



Hide 8219B 19.INSTALL FRONT SEAT NO. 2 WIRE (w/ Lumbar Support)

a.
B491295

Engage the clamp to install the front seat No. 2 wire.


Hide 71759D 20.INSTALL FRONT NO. 2 SEATBACK HOOK

a.
B429312

Install the 2 front No. 2 seatback hooks to the front seatback frame sub-assembly.


Hide 71587 21.INSTALL FRONT SEATBACK EDGE PROTECTOR

a.

w/o Lumbar Support:

i.

Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.



b.

w/ Lumbar Support:

i.

Install the 2 front seatback edge protectors to the lumbar support adjuster assembly RH.



Hide 72750D 22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (w/ Lumbar Support)

Hide 71053S 23.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)

a.
B489769C02
0,0 0,0 false
V113147

Install in this Direction


Install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.


b.
B489770

Engage the 2 claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.


Hide 73910A 24.INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

Hide 87510M 25.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)

Hide 71073S 26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.
B471091

Engage the 9 claws to install the separate type front seatback cover to the separate type front seatback pad.


Hide 27.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.

Install the separate type front seatback cover with pad.


Hide 71931 28.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B471082

Engage the 4 claws to install the 2 front seat headrest supports.


b.

w/o Rear Seat Belt Warning:

i.
B456132C02
0.531,1.594 1.635,1.594 true 1.813,1.875 1.813,1.51 true 0.323,1.51 0.531,1.688 0.208,0.177 10 false *1 1.75,1.896 2.063,2.052 0.313,0.156 10 false *a
*1 Seat Cover Hanger
*a Bracket
V113147

Install in this Direction


Slide the bracket as shown in the illustration to engage the hook and connect the bracket to the seat cover hanger.

NOTICE:
·

For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

·

Make sure that the strap is not twisted after connecting the bracket to the seat cover hanger.

·

Install the bracket securely.




ii.
B456125C02
1.76,1.604 3.063,1.604 true 0.531,2.26 1.021,2.26 false 3.094,1.521 3.333,1.698 0.24,0.177 10 false *1 0.354,2.177 0.667,2.375 0.313,0.198 10 false *a
*1 Seatback Cover Hook
*a Pin


Insert the seatback cover hook and push in the pin to install it as shown in the illustration.


iii.
B456142C03
0,0 0,0 false
V113147

Install in this Direction


Engage the hook as shown in the illustration.



c.
B429322

Close the 2 fasteners.


d.

w/ Seat Heater System:

i.
B491321

Engage the clamp.



e.
B489756

Engage the 3 hooks.


Hide 29.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B489755

Engage the 4 guides.


b.

Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

w/ Front Seat Side Airbag:

i.
B489744

Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.

HINT:

Engage the claw first.




d.

w/ Seat Heater System:

i.
B491320

Engage the clamp.


ii.

Connect the connector.



e.

w/ Lumbar Support:

i.
B491293

Engage the clamp.


ii.

Connect the connector.



f.
B489743

Engage the 2 hooks.


g.
B447549

Pass the separate type front seatback cover through the grooves of the LH seat reclining adjuster inside cover LH and LH seat reclining adjuster inside cover RH.


Hide 72136C 30.INSTALL LOWER NO. 4 SEAT TRACK SPACER (w/o Vertical Adjuster)

a.

w/ Lower Seat Track Spacer:

i.
B477730

Engage the claw and guide to install the lower No. 4 seat track spacer to the front seat inner cushion shield.



Hide 72136B 31.INSTALL LOWER NO. 3 SEAT TRACK SPACER (w/o Vertical Adjuster)

a.

w/ Lower Seat Track Spacer:

i.
B477935

Engage the claw and guide to install the lower No. 3 seat track spacer to the front seat cushion shield.



Hide 72136A 32.INSTALL LOWER NO. 2 SEAT TRACK SPACER (w/ Vertical Adjuster)

a.

w/ Lower Seat Track Spacer:

i.
B477728

Engage the claw and guide to install the lower No. 2 seat track spacer to the front seat inner cushion shield.



Hide 72136 33.INSTALL LOWER NO. 1 SEAT TRACK SPACER (w/ Vertical Adjuster)

a.

w/ Lower Seat Track Spacer:

i.
B477729

Engage the claw and guide to install the lower No. 1 seat track spacer to the front seat cushion shield.



Hide 71861 34.INSTALL FRONT SEAT INNER CUSHION SHIELD (w/o Vertical Adjuster)

a.
B431138C03
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws and 2 guides as shown in the illustration.


b.
B489749

Engage the 3 claws to install the front seat inner cushion shield.


Hide 71811D 35.INSTALL FRONT SEAT CUSHION SHIELD (w/o Vertical Adjuster)

a.
B491210C02
0.667,0.365 1.833,0.365 true 0.917,0.667 1.333,0.667 1.333,0.667 1.333,0.365 true 2.417,1.458 3,1.458 true 1.885,0.302 2.042,0.5 0.156,0.198 10 true B 3.042,1.375 3.198,1.573 0.156,0.198 10 true A
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide (A) as shown in the illustration.


b.

Engage the 2 claws and 2 guides (B) as shown in the illustration.


c.
B489745

Engage the 2 claws to install the front seat cushion shield.


Hide 71861 36.INSTALL FRONT SEAT INNER CUSHION SHIELD (w/ Vertical Adjuster)

a.
B489771C03
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws and 2 guides as shown in the illustration.


b.
B489739

Engage the 2 claws to install the front seat inner cushion shield.


Hide 84922A 37.INSTALL FRONT LUMBAR POWER SEAT SWITCH (w/ Lumbar Support)

Hide 71811D 38.INSTALL FRONT SEAT CUSHION SHIELD (w/ Vertical Adjuster)

a.

w/ Lumbar Support:

i.
B491292

Connect the front lumbar power seat switch connector.


ii.

Engage the 2 clamps.



b.
B489772C02
1.594,0.208 2.51,0.208 true 0.281,1.438 0.615,1.438 true 2.021,0.208 2.021,0.458 2.021,0.458 2.354,0.458 true 0.125,1.354 0.281,1.552 0.156,0.198 10 true A 1.417,0.135 1.573,0.333 0.156,0.198 10 true B
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide (A) as shown in the illustration.


c.

Engage the 3 claws and 2 guides (B) as shown in the illustration.


d.
B489735

Engage the 2 claws to install the front seat cushion shield.


Hide 71848A 39.INSTALL SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)

a.
B489773C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides as shown in the illustration.


b.

Engage the 2 claws to install the seat adjuster cover cap as shown in the illustration.


Hide 72525A 40.INSTALL RECLINING ADJUSTER RELEASE HANDLE

a.
B489733

Install the reclining adjuster release handle.


Hide 72551B 41.INSTALL RECLINING HINGE COVER

a.
B491211

Engage the guide.


b.

Engage the claw to install the reclining hinge cover.


Hide 72494 42.INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)

a.
B489774C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the vertical adjusting handle as shown in the illustration.


Hide 71073S 43.CONNECT SEPARATE TYPE FRONT SEATBACK COVER

a.
B489730

Connect the rubber band of the separate type front seatback cover.


Hide 73230 44.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

Hide 73240 45.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

Hide 89952 46.INSTALL OCCUPANT DETECTION ECU (w/ Occupant Classification System)