1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
w/ Claw:
Engage the 2 claws.
Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Connect each connector.
| *A | for LHD | *B | for RHD |
| *C | w/o Seat Heater | *D | w/ Seat Heater |
|
Install in this Direction | - | - |
Engage each clamp.
Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
Install the 4 bolts (A).
Connect the brake pedal assembly with the bolt (B).
Temporarily install the nut.
Install the 3 bolts.
Install the 2 hole plugs.
| *a | Lip |
Install a new cooler unit drain hose grommet.
If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.
Connect the drain cooler hose.
Install the front floor mat to its original position as shown in the illustration.
| *a | Lock Lever |
|
Move in this Direction |
Engage each clamp.
Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connector.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Check that there is no looseness in the installed parts of the airbag sensor assembly.
Connect the connector.
for LHD:
Engage each clamp.
Connect the connector holder with the 2 nuts.
Connect the 3 earth wires with the 3 bolts.
Connect the connector.
for RHD:
Engage the clamp.
Connect the connector holder with the 2 nuts.
Engage each clamp.
Connect the 3 earth wires with the 3 bolts.
Connect each connector.
87201B
3.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
Engage the 4 claws to install the No. 2 air duct sub-assembly.
4.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)
89980
5.INSTALL HYBRID VEHICLE CONTROL ECU ASSEMBLY (for LHD)
82877
6.INSTALL ECU INTEGRATION BOX RH (for RHD)
55308B
7.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.
Engage each clamp.
55307C
8.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Engage each clamp.
for LHD:
Connect the relay block assembly with the bolt (B).
Connect the earth wire with the bolt (A).
for RHD:
Connect the earth wire with the bolt.
55306A
9.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Engage each clamp.
for LHD:
Connect the earth wire with the bolt.
for RHD:
Connect the relay block assembly with the bolt (B).
Connect the earth wire with the bolt (A).
10.INSTALL AIR CONDITIONER UNIT ASSEMBLY
for LHD:
Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.
|
Bolt |
|
Screw |
|
Nut | - | - |
Tighten the bolts, screws and nut in the order shown in the illustration.
for RHD:
Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.
|
Bolt |
|
Screw |
|
Nut | - | - |
Tighten the bolts, screws and nut in the order shown in the illustration.
55215D
11.INSTALL NO. 3 DASH PANEL INSULATOR PAD
Install the No. 3 dash panel insulator pad with 2 new clips as shown in the illustration.
58861B
12.INSTALL NO. 1 CONSOLE BOX DUCT
|
Install in this Direction |
Install the No. 1 console box duct as shown in the illustration.
58544B
13.INSTALL FLOOR CARPET BRACKET LH
|
Install in this Direction |
Engage the claw as shown in the illustration.
Install the floor carpet bracket LH with the clip.
58543B
14.INSTALL FLOOR CARPET BRACKET RH
|
Install in this Direction |
Engage the claw as shown in the illustration.
Install the floor carpet bracket RH with the clip.
87212G
15.INSTALL REAR NO. 3 AIR DUCT
Engage the 2 claws to install the rear No. 3 air duct.
87212H
16.INSTALL REAR NO. 4 AIR DUCT
|
Install in this Direction |
Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.
Install the front floor carpet assembly to its original position as shown in the illustration.
Engage the 2 guides.
Install the 2 front floor carpet clips.
87212
17.INSTALL REAR NO. 1 AIR DUCT
Engage the 2 claws to install the rear No. 1 air duct.
87212F
18.INSTALL REAR NO. 2 AIR DUCT
|
Install in this Direction |
Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.
Install the front floor carpet assembly to its original position as shown in the illustration.
Engage the 2 guides.
Install the front floor carpet clip.
for LHD:
Install the front floor carpet clip.
58569D
19.INSTALL FRONT FLOOR CAUTION PLATE COVER
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide and claw to install the front floor caution plate cover as indicated by the arrows, in the order shown in the illustration.
78111
20.INSTALL ACCELERATOR PEDAL
78118
21.INSTALL ACCELERATOR PEDAL PAD
88625Q
22.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR
Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.
82877
23.INSTALL ECU INTEGRATION BOX RH (for LHD)
24.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)
89980
25.INSTALL HYBRID VEHICLE CONTROL ECU ASSEMBLY (for RHD)
89343C
26.INSTALL NO. 1 CLEARANCE WARNING BUZZER (for LHD)
27.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
45250
28.INSTALL STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
for Power Tilt and Power Telescopic Steering Column:
29.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
30.INSTALL FRONT SEAT ASSEMBLY LH
for Manual seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION
31.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
88710E
32.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the air conditioning tube and accessory assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.
ND-OIL 11 or equivalent
Install the O-ring to the air conditioning tube and accessory assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the air conditioning tube and accessory assembly.
88707
33.CONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the vinyl tape from the suction pipe sub-assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
ND-OIL 11 or equivalent
Install the O-ring to the suction pipe sub-assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction pipe sub-assembly.
Rotate the hook connector as shown in the illustration.
Insert the tube joint into the fitting hole securely and install the bolt.
87245
34.CONNECT INLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (White) |
| *c | Clip Installation Angle (270°) |
Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
87246
35.CONNECT OUTLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (Red) |
| *c | Clip Installation Angle (270°) |
Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the outlet heater water hose.
53607A
36.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>INSTALLATION
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>INSTALLATION
37.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
38.ADD ENGINE COOLANT (for Engine)
39.INSPECT FOR COOLANT LEAK (for Engine)
40.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
41.WARM UP COMPRESSOR
42.INSPECT FOR REFRIGERANT LEAK