The battery cooling blower assembly speed is controlled by the hybrid vehicle control ECU assembly. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU assembly turns on the IGCT relay. The hybrid vehicle control ECU assembly sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the hybrid vehicle control ECU assembly via the battery voltage sensor as a monitor signal using serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A8111 | Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground | Both of the following conditions are met:
·
The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range. ·
The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking). (1 trip detection logic: w/ Canister Pump Module) (2 trip detection logic: w/o Canister Pump Module) |
·
Battery voltage sensor ·
Hybrid vehicle control ECU assembly ·
Battery cooling blower assembly ·
BATT FAN fuse ·
Wire harness or connector |
Comes on (w/ Canister Pump Module) / Does not come on (w/o Canister Pump Module) | Master Warning Light:
Comes on |
| P0A814B | Hybrid/EV Battery Cooling Fan 1 Over Temperature | Both of the following conditions are met:
·
The HV battery temperature is high and the speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range. ·
The HV battery temperature is high and the battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking). (1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid vehicle control ECU assembly ·
Battery cooling blower assembly ·
BATT FAN fuse ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A8111 | ·
Hybrid Battery Cooling Fan 1 Drive Request ·
Hybrid Battery Cooling Fan 1 Drive Status ·
Hybrid Battery Cooling Fan 1 Frequency |
| P0A814B |
The following items can be helpful when performing repairs:
Hybrid Battery Temperature 1 to 3
BATT Voltage
"Hybrid Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
Select fan mode 1 and operate the battery cooling blower assembly and wait for 60 seconds or more.
Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00 or P0AFC96 is not output. | A |
| P0AFC00 or P0AFC96 is output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Change the battery cooling blower assembly operation and blower volume. | 0, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Select fan mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.
Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.
The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.
The battery cooling blower assembly operates.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Disconnect the R21 battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R21-8 (FP0) - R24-1 (FP0) | Power switch off | Below 1 Ω |
| R21-8 (FP0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R21-8 (FP0) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the R24 battery cooling blower assembly connector.
Reconnect the R21 battery voltage sensor connector.
Install the No. 1 hybrid battery exhaust duct.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Change the battery cooling blower assembly operation and blower volume. | 0, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan 1 Frequency.
| Tester Display |
|---|
| Hybrid Battery Cooling Fan 1 Frequency |
Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan assembly.
| *a | Component with harness connected
(Battery Voltage Sensor) |
While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.
| Tester Connection | Condition |
|---|---|
| R21-8 (FP0) - R21-5 (GND) | Battery cooling blower assembly is operating. |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.
| Result | Proceed to |
|---|---|
| Both of the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. | A |
| Other than above | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 hybrid battery exhaust duct.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling bower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-1 (FP0) - R24-3 (GND0) | Power switch on (IG) | 4.5 to 5.5 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Change the battery cooling blower assembly operation and blower volume. | 0, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan 1 Frequency.
| Tester Display |
|---|
| Hybrid Battery Cooling Fan 1 Frequency |
Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.
| *a | Component with harness connected
(Battery Voltage Sensor) |
While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R21-8 (FP0) - R21-5 (GND) | Battery cooling blower assembly is operating. | Difference between the value in the Data List (Hybrid Battery Cooling Fan 1 Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less. |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Compare the values in each fan mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current fan mode.
| Proceed to |
|---|
| OK |
| NG |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 hybrid battery exhaust duct.
OK
NG
| *1 | No. 4 Relay Block |
| *2 | BATT FAN Fuse |
Remove the BATT FAN fuse from the No. 4 relay block.
Measure the resistance of the BATT FAN fuse.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BATT FAN fuse | Power switch off | Below 1 Ω |
Install the BATT FAN fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-2 (IG0) - R24-3 (GND0) | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)
Fuse condition (before and after removing fuse(s)) (IG circuit)
Connection condition of connectors (IG circuit)
Wire harness condition (IG circuit)
Wire harness condition (GND circuit)
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check the terminals of the connector for deformation and corrosion.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-29 (SI0) - R24-4 (SI0) | Power switch off | Below 1 Ω |
| R24-4 (SI0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Make sure that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-4 (SI0) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Check that each connector between the hybrid vehicle control ECU assembly and battery cooling blower assembly is not loose or disconnected.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the hybrid vehicle control ECU assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
| *a | Component without harness connected
(Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-29 (SI0) - K69-5 (E01) | Power switch off | 10 kΩ or higher |
Install the hybrid vehicle control ECU assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-29 (SI0) - K69-5 (E01) | Power switch on (IG) | 4.5 to 5.5 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Change the battery cooling blower assembly operation and blower volume. | 0, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Select each fan mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling blower assembly.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Connect an oscilloscope to the K69 and K70 hybrid vehicle control ECU assembly connector and check the waveform.
| Item | Content |
|---|---|
| Tester Connection | K70-29 (SI0) - K69-5 (E01) |
| Equipment Setting | 10 V/DIV., 1 ms./DIV. |
| Condition | Power switch on (IG), during Active Test |
Perform this inspection with the hybrid vehicle control ECU assembly connector connected.
The wave length will vary with the operating speed of the battery cooling blower assembly.
Turn the power switch off.
| *a | Waveform 1 |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| Result | Proceed to |
|---|---|
| Normal (The pulse output of waveform 1) | A |
| No pulse generation | B |
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-3 (GND0) - Body ground | Power switch off | Below 1 Ω |
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K69 hybrid vehicle control ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K69-5 (E01) - Body ground | Power switch off | Below 1 Ω |
Reconnect the K69 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-5 (E02) - Body ground | Power switch off | Below 1 Ω |
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the IGCT relay from the No. 6 relay block.
Check the terminals of the relay for deformation and corrosion.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.
Before disconnecting the connector, check that it is not loose or disconnected.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 6 Relay Block | - | - |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
*b | IGCT Relay Terminal |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IGCT relay terminal 5 - R24-2 (IG0) | Power switch off | Below 1 Ω |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
Install the IGCT relay to the No. 6 relay block.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the BATT FAN fuse from the No. 4 relay block.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *1 | No. 4 Relay Block |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | BATT FAN Fuse Terminal |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-2 (IG0) - Terminals other than 2 (BATT FAN fuse) and body ground | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
Install the BATT FAN fuse to the No. 4 relay block.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion leg sub-assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
Disconnect the R24 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Component without harness connected
(Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R24-2 (IG0) - R24-3 (GND0) and Body ground | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the R24 battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT