These DTCs are stored when a malfunction occurs in the roof antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Disconnected (Short) | Current to the roof antenna assembly is lower than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Short circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 5 antenna cord sub-assembly |
| B15C1 | GPS Antenna Disconnected (Open) | Current to the roof antenna assembly is higher than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Open circuit) |
·
Telematics transceiver ·
Roof antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
No. 5 antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 10 seconds or more.
Turn the GTS on.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the No. 5 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(No. 5 Antenna Cord Sub-assembly) |
| *a | Component without harness connected
(No. 5 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-2 - G-2 | Always | Below 1 Ω |
| F-2a - G-2a | Always | Below 1 Ω |
| F-2 or G-2 - Body ground | Always | 10 kΩ or higher |
| F-2a or G-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-2 - E-2 | Always | Below 1 Ω |
| D-2a - E-2a | Always | Below 1 Ω |
| D-2 or E-2 - Body ground | Always | 10 kΩ or higher |
| D-2a or E-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(Antenna Cord Sub-assembly) |
| *a | Component without harness connected
(Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 - C-2 | Always | Below 1 Ω |
| A-1a - C-2a | Always | Below 1 Ω |
| A-1 or C-2 - Body ground | Always | 10 kΩ or higher |
| A-1a or C-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT