The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Map Light (Roof Console Box Sub-assembly)*1
Spot Light Assembly*1
Room Light Assembly*2
*1: w/ Room Light (for LED Type)
*2: w/ Room Light (for Bulb Type)
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Turns on the lights that are controlled by the illuminated entry system* | OFF or ON | w/ Room Light (for LED Type):
Perform the Active Test with the door linked switch of the map light (roof console box sub-assembly) on and switches of the spot light assembly LH and RH off. w/ Room Light (for Bulb Type): Perform the Active Test with switch of the room light assembly in the DOOR position. |
*: Refer to System Description for the lights that are controlled by the illuminated entry system.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION
| Tester Display |
|---|
| Illuminated Entry System |
All lights that are controlled by the illuminated entry system come on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Map light (roof console box sub-assembly) and/or spot light assembly do not come on (w/ Room Light (for LED Type))) | B |
| NG (Room light assembly does not come on (w/ Room Light (for Bulb Type))) | C |
A
B
C
Remove the map light (roof console box sub-assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Inspect the map light (roof console box sub-assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spot light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL
Inspect the spot light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-1 (+B1) - V11-5 (B) | Always | Below 1 Ω |
| V12-2 (RLMP) - V11-2 (CTY) | Always | Below 1 Ω |
| V12-1 (+B1) or V11-5 (B) - Body ground | Always | 10 kΩ or higher |
| V12-2 (RLMP) or V11-2 (CTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V18-10 (+B1) - V11-5 (B) | Always | Below 1 Ω |
| V18-2 (RLMP) - V11-2 (CTY) | Always | Below 1 Ω |
| V18-10 (+B1) or V11-5 (B) - Body ground | Always | 10 kΩ or higher |
| V18-2 (RLMP) or V11-2 (CTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V14-14 (+B1) - V11-5 (B) | Always | Below 1 Ω |
| V14-2 (RLMP) - V11-2 (CTY) | Always | Below 1 Ω |
| V14-14 (+B1) or V11-5 (B) - Body ground | Always | 10 kΩ or higher |
| V14-2 (RLMP) or V11-2 (CTY) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-10 - V12-1 (+B1) | Always | Below 1 Ω |
| 3B-29 - V12-3 (DOOR) | Always | Below 1 Ω |
| 3B-10 or V12-1 (+B1) - Body ground | Always | 10 kΩ or higher |
| 3B-29 or V12-3 (DOOR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-10 - V18-10 (+B1) | Always | Below 1 Ω |
| 3B-29 - V18-1 (DOOR) | Always | Below 1 Ω |
| 3B-10 or V18-10 (+B1) - Body ground | Always | 10 kΩ or higher |
| 3B-29 or V18-1 (DOOR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-10 - V14-14 (+B1) | Always | Below 1 Ω |
| 3B-29 - V14-1 (DOOR) | Always | Below 1 Ω |
| 3B-10 or V14-14 (+B1) - Body ground | Always | 10 kΩ or higher |
| 3B-29 or V14-1 (DOOR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-10 - 3B-29 | Room light switch in DOOR position | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-29 - MB-1 (ILE) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG