Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › 2019.10–2020.08
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324468 ENGINE UNIT A

A25A-FXS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 17169A 1.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Type A:

i.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



b.

Type B:

i.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



Hide 11452 2.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250E 5.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23800 11.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82126A 13.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 14.INSTALL SENSOR WIRE

a.

Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 3 clamps.


c.

Connect the 4 connectors.


Hide 16295 15.INSTALL NO. 7 WATER BY-PASS HOSE

a.

Install the No. 7 water by-pass hose and slide the 2 clips to secure it.


Hide 23100X 16.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 17.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 18.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 19.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

for EGR Valve Bracket Connection Type:

i.
A407621C02
2.792,2.729 2.833,2.365 2.833,2.365 2.979,2.365 false 3.042,2.292 3.354,2.49 0.313,0.198 10 false *a 1.552,2.354 1.865,2.552 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




ii.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)





b.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A471092C01
2.792,2.729 2.833,2.365 2.833,2.365 2.979,2.365 false 3.042,2.292 3.354,2.49 0.313,0.198 10 false *a 1.552,2.354 1.865,2.552 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




ii.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




iii.

Using an 8 mm socket wrench, install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 17177 21.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 16278 23.INSTALL NO. 2 WATER BY-PASS PIPE

a.
A406696N03
1.813,0.958 1.969,1.156 0.156,0.198 10 true B 1.125,1.604 1.281,1.802 0.156,0.198 10 true B 2.615,1.885 2.771,2.083 0.156,0.198 10 true A

Install the bolt (A).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16279 24.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.


b.

Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25620 25.INSTALL EGR VALVE ASSEMBLY

a.

Using an 8 mm socket wrench, install the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

for EGR Valve Bracket Connection Type:

i.
A488210C01
2.313,0.802 2.552,0.448 2.552,0.448 2.677,0.448 true 2.333,0.938 2.552,0.938 true 2.604,0.844 2.917,1.042 0.313,0.198 10 true *a 2.74,0.313 3.052,0.51 0.313,0.198 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.


ii.

Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Using the 8 mm socket wrench, connect the No. 1 fuel pipe sub-assembly to the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A471093C01
2.344,0.74 2.552,0.448 2.552,0.448 2.677,0.448 true 2.385,0.865 2.604,0.865 true 2.635,0.781 2.948,0.979 0.313,0.198 10 true *a 2.74,0.313 3.052,0.51 0.313,0.198 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.


ii.

Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



d.

Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


Hide 26.INSTALL WATER HOSE

a.

w/ Water Hose Connector:

i.
A406701C02
1.104,2.385 1.323,2.385 false 0.906,2.302 1.219,2.5 0.313,0.198 10 false *a
*a Retainer
V100135

Push in


Install the water hose to the EGR valve assembly.

Align the water hose with the EGR valve assembly, push the water hose onto the EGR valve assembly, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.



ii.

Check that the EGR valve assembly and water hose are securely connected by pulling on them.



b.

w/o Water Hose Connector:

i.

Install the water hose to the EGR valve assembly and slide the clip to secure it.



Hide 25601 27.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25680 28.INSTALL EGR COOLER ASSEMBLY

a.

Install the EGR cooler assembly, a new EGR cooler gasket and a new EGR valve gasket with the 5 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.


c.

Connect the water hose to the EGR cooler assembly and slide the clip to secure it.


Hide 22271 29.INSTALL THROTTLE BODY GASKET

Hide 22030 30.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17167 33.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

w/o Differential Pressure Sensor, Type A:

i.
A404785

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

w/o Differential Pressure Sensor, Type B:

i.
A484562

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

w/ Differential Pressure Sensor:

i.
A450072

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 25706 34.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)

a.
A450075C01
1.927,0.354 2.24,0.552 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).




b.

Install the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY (w/ Differential Pressure Sensor)

a.

Connect the vacuum transmitting hose assembly to the No. 1 vacuum transmitting pipe sub-assembly and slide the clip to secure it.


Hide 89481B 36.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)

Hide 16260 37.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A409020N01
0.99,0.385 1.146,0.583 0.156,0.198 10 true A 0.948,0.792 1.104,0.99 0.156,0.198 10 true B

Install the water hose clamp bracket with the 2 bolts as shown in the illustration.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



b.
A406702C02
1,3.865 1,3.323 true 0.906,3.927 1.219,4.125 0.313,0.198 10 false *a 2.875,2.802 3.188,3 0.313,0.198 10 false *b 2.906,3.563 3.219,3.76 0.313,0.198 10 false *b
*a Paint Mark
*b 45° (Claw of Clip Location)


Connect the flow shutting valve (water by-pass hose assembly) to the outlet water by-pass sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the outlet water by-pass sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




c.

Install the flow shutting valve (water by-pass hose assembly) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16207 38.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.


Hide 88370 39.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.

Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
E371430C03
1.333,1.917 1.49,2.115 0.156,0.198 10 false 1 0.594,1.802 0.75,2 0.156,0.198 10 false 2 0.75,0.167 0.906,0.365 0.156,0.198 10 false 3
V100135

Bolt
V100136

Nut


Install the compressor with motor assembly with the bolt and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolt and nuts in the order shown in the illustration.



Hide 43457 40.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:

Make sure that the bolts and bolt holes are free of oil. Clean them if necessary.