Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2020.08–2021.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328993 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Parking Support Brake System*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)



PROCEDURE

Hide 82111 2.DISCONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A406211

Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.

NOTICE:
·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Insulate the disconnected terminals with insulating tape.

·

Do not touch the waterproof seal or terminals of the connector.




Hide 5.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 73350C 7.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 8.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

Hide 71033 15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N4A 16.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 17.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406214C01
1.896,1.427 2.313,1.427 true 1.885,3.729 2.302,3.729 true 0.052,0.302 0.344,0.531 0.292,0.229 12 true *A 0.042,2.615 0.323,2.823 0.281,0.208 12 true *B 2.333,1.323 2.552,1.51 0.219,0.188 10 true *a 2.323,3.625 2.542,3.813 0.219,0.188 10 true *a
*A for NICKEL METAL HYDRIDE BATTERY
*B for LITHIUM-ION BATTERY
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


c.
A406076

Disconnect the floor wire connector.


Hide 17410 18.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58398F 20.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58223 21.REMOVE CENTER NO. 2 FLOOR HEAT INSULATOR

a.
A406216

Remove the 3 nuts and center No. 2 floor heat insulator.


Hide 33820B 22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A406758

Remove the 2 nuts and disconnect the transmission control cable assembly.


Hide 821H1 23.REMOVE HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A406742

Remove the 2 nuts.


b.

Remove the 2 clamps.

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A406743

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.
A406744

Remove the 3 nuts.


e.
A406745

Remove the 2 nuts and clamp.

NOTICE:

If the clamp is removed forcibly, the stud bolt may be damaged.



f.
A406746

Disengage the clamp.


g.

Disconnect the HV floor under wire connector.


h.

Remove the nut and HV floor under wire.