The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
53851M
1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
53852K
2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
51441
3.REMOVE NO. 1 ENGINE UNDER COVER
4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)
5.DRAIN ENGINE COOLANT (for Engine)
G9040
6.REMOVE INVERTER WATER PUMP ASSEMBLY
7.REMOVE HEADLIGHT ASSEMBLY
for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
52611
8.REMOVE FRONT BUMPER ENERGY ABSORBER
52131A
9.REMOVE FRONT BUMPER REINFORCEMENT
53019F
10.REMOVE RADIATOR SHUTTER SUB-ASSEMBLY
53510
11.REMOVE HOOD LOCK ASSEMBLY
17750A
12.REMOVE INLET AIR CLEANER ASSEMBLY
53253B
13.REMOVE UPPER RADIATOR MOUNTING BRACKET
| *A | for LHD |
| *B | for RHD |
w/ Vehicle Approaching Speaker Switch
Disconnect the 2 horn connectors.
Disconnect the vehicle approaching speaker assembly connector.
w/o Vehicle Approaching Speaker Switch
Disconnect the 2 horn connectors.
Remove the 2 bolts, 2 nuts and 2 upper radiator mounting brackets.
16595B
14.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/ Grille Shutter)
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide LH.
16595B
15.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/o Grille Shutter)
| *1 | No. 1 Radiator Air Guide LH |
| *2 | Front Radiator Side Air Guide Plate LH |
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide LH with the front radiator side air guide plate LH.
16593B
16.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/ Grille Shutter)
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide RH.
16593B
17.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/o Grille Shutter)
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide RH.
53205
18.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
Remove the 4 bolts and upper radiator support sub-assembly.
16281F
19.DISCONNECT NO. 5 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 5 water by-pass hose from the radiator assembly.
16283D
20.DISCONNECT NO. 6 WATER BY-PASS HOSE
Disconnect the No. 6 water by-pass hose from the radiator assembly.
16571C
21.DISCONNECT NO. 1 RADIATOR HOSE
Disengage the clamp and disconnect the No. 1 radiator hose from the fan with motor assembly.
Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.
G9228A
22.DISCONNECT NO. 4 INVERTER COOLING HOSE
Slide the clip and disconnect the No. 4 inverter cooling hose from the radiator assembly.
G9229A
23.DISCONNECT NO. 5 INVERTER COOLING HOSE
Disengage the 2 clamps and disconnect the No. 5 inverter cooling hose from the fan with motor assembly.
G9226A
24.DISCONNECT NO. 2 INVERTER COOLING HOSE
Disengage the clamp and disconnect the No. 2 inverter cooling hose from the fan with motor assembly.
16572D
25.DISCONNECT NO. 2 RADIATOR HOSE
Disengage the clamp and disconnect the No. 2 radiator hose from the fan with motor assembly.
Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.
G9227A
26.REMOVE NO. 3 INVERTER COOLING HOSE
Disengage the clamp and disconnect the No. 3 inverter cooling hose from the fan with motor assembly.
Slide the clip and remove the No. 3 inverter cooling hose from the radiator assembly.
16400
27.REMOVE RADIATOR ASSEMBLY
Disengage the 4 clamps to disconnect the wire harness from the fan with motor assembly.
Disconnect the cooling fan motor connector.
Disengage the wire harness clamp.
Rotate the lever while pushing the lock, and disconnect the cooling fan motor connector.
After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.
Disengage the wire harness clamp.
Disengage the 2 claws.
Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.
Make sure not to damage the cooler condenser assembly when separating the cooler condenser assembly.
Remove the radiator assembly with the fan with motor assembly from the vehicle body.
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan with motor assembly.
Disengage the 2 claws.
Disengage the 2 guides to remove the fan with motor assembly from the radiator assembly.
Do not damage the radiator assembly when removing the fan with motor assembly.
16523A
28.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
29.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.