The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION
for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
| *a | Object Exceeding Weight Limit of Transmission Jack |
The hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)
If the ECM has been struck or dropped, replace it.
Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION
w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION
1. PERFORM RESOLVER INITIALIZATION
If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.
for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY
for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY
2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
23825
3.REMOVE FUEL DELIVERY GUARD
4.INSTALL ENGINE HANGERS
45319
5.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)
82121
6.DISCONNECT ENGINE WIRE (for LHD)
Remove the 2 bolts.
Disconnect the 5 clamps.
Disconnect the wire harness connector from the rack and pinion power steering gear assembly.
Release the lock before rotating the lock lever.
Remove the 2 bolts and separate the wire harness from the rack and pinion power steering gear assembly.
82121
7.DISCONNECT ENGINE WIRE (for RHD)
Remove the 2 bolts.
Disconnect the 6 clamps.
Disconnect the wire harness connector from the rack and pinion power steering gear assembly.
Release the lock before rotating the lock lever.
821H2
8.DISCONNECT HV AIR CONDITIONING WIRE
Remove the bolt.
Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.
28193
9.REMOVE STARTER HOLE INSULATOR
Remove the 2 bolts and starter hole insulator from the engine assembly.
11363A
10.REMOVE FLYWHEEL HOUSING SIDE COVER
Remove the flywheel housing side cover from the engine assembly.
51100G
11.REMOVE FRONT FRAME ASSEMBLY
12361A
12.REMOVE FRONT ENGINE MOUNTING INSULATOR
Remove the bolt and front engine mounting insulator from the front engine mounting bracket.
12311A
13.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the hybrid vehicle transaxle assembly.
12371A
14.REMOVE REAR ENGINE MOUNTING INSULATOR
12303
15.REMOVE REAR ENGINE MOUNTING BRACKET
Remove the 4 bolts and rear engine mounting bracket from the hybrid vehicle transaxle assembly.
30900
16.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
Remove the 8 bolts and hybrid vehicle transaxle assembly from the engine assembly.
To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.
To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.
G1148
17.REMOVE MOTOR CABLE
G125A
18.REMOVE MOTOR COOLING COOLER
33823
19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.
44781E
20.REMOVE HOSE BRACKET
Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.
82125
21.REMOVE TRANSMISSION WIRE
Disconnect the connector.
Remove the bolt and transmission wire from the hybrid vehicle transaxle assembly.
22.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 4 bolts and 4 wire harness clamp brackets from the hybrid vehicle transaxle assembly.
23.REMOVE TRANSAXLE HOUSING PLUG
Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.
24.REMOVE STUD BOLT
Using a E10 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.