Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2019.10
RM33C0E _51 Engine / Hybrid System _065423 A25A-FXS INTAKE / EXHAUST _0322981 EXHAUST MANIFOLD A

A25A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 58166A 1.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 2.REMOVE FRONT FLOOR COVER RH (w/ Cover)

Hide 57533B 3.REMOVE FRONT CENTER FLOOR BRACE

Hide 57523A 4.REMOVE CENTER FLOOR CROSSMEMBER BRACE

Hide 17410 5.REMOVE FRONT EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402297

Disengage the wire harness clamp.


b.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


c.
A402298

Remove the 2 bolts, 2 nuts and disconnect the front exhaust pipe assembly from the exhaust manifold and center exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly from the 2 exhaust pipe supports.


e.

Remove the 2 gaskets from the front exhaust pipe assembly.


Hide 58152A 6.REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

Hide 53851M 7.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (w/ Cover)

Hide 53852K 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (w/ Cover)

Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER (w/ Cover)

Hide 10.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 55708 11.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 12.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 13.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 89467B 14.REMOVE AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 15.REMOVE WIRE HARNESS CLAMP BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402299

Remove the bolt and wire harness clamp bracket.


Hide 25706 16.SEPARATE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A445026

Remove the nut.


b.
A445027

Using a 14 mm union nut wrench, separate the No. 1 vacuum transmitting pipe sub-assembly from the exhaust manifold.


Hide 17167 17.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.

Type A:

i.
A402300

Remove the 5 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold.



b.

Type B:

i.
A479124

Remove the 3 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold.



c.

Type C, Type D:

i.
A449055

Remove the 3 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold.



Hide 58151 18.SEPARATE NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402301

Remove the 2 nuts and separate the No. 1 upper front floor heat insulator from the vehicle body.


Hide 17118 19.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402302

Remove the bolt, nut and manifold stay from the exhaust manifold and cylinder block sub-assembly.


Hide 17141 20.REMOVE EXHAUST MANIFOLD

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402303

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.


b.

Remove the No. 1 upper front floor heat insulator, No. 1 exhaust manifold heat insulator and exhaust manifold.


c.
A402304

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 21.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402265

Type A, Type C:

i.

Remove the 6 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold.



b.
A462942

Type B, Type D:

i.

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold.