89341K
1.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
w/o Parking Support Brake System:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
89347B
2.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
w/o Parking Support Brake System:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
89341L
3.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
w/ Parking Support Brake System:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
89341K
4.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
w/ Parking Support Brake System:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
89347B
5.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
w/ Parking Support Brake System:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
82114
6.REMOVE NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
for Bar Type Radiator Grille:
Disengage the 7 clamps to remove the No. 4 engine room wire.
for Mesh Type Radiator Grille:
Disengage the 12 clamps to remove the No. 4 engine room wire.
88211B
7.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
52114A
8.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)
Remove the 2 screws.
|
Remove in this Direction |
Disengage the 4 claws to remove the front bumper extension mounting bracket as shown in the illustration.
52114A
9.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)
Remove the 2 screws.
|
Remove in this Direction |
Disengage the 2 claws and 4 guides to remove the front bumper extension mounting bracket as shown in the illustration.
52423A
10.REMOVE FRONT BUMPER PAD LH (for Bar Type Radiator Grille)
Remove the front bumper pad LH.
52422A
11.REMOVE FRONT BUMPER PAD RH (for Bar Type Radiator Grille)
Use the same procedure as for the LH side.
52423A
12.REMOVE FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)
Disengage the 2 claws and guide to remove the front bumper pad LH.
52422A
13.REMOVE FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
86790B
14.REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Bar Type Radiator Grille:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL
15.REMOVE FRONT BUMPER COVER INSERT (w/ Panoramic View Monitor System)
for Mesh Type Radiator Grille:
Disengage the 2 claws to remove the front bumper cover insert.
86790B
16.REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Mesh Type Radiator Grille:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL
85354
17.REMOVE HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)
85353
18.REMOVE HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
85208A
19.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A
20.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
21.REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
Disengage the 7 clamps to remove the headlight cleaner hose.
52128B
22.REMOVE FRONT BUMPER HOLE COVER LH (for Bar Type Radiator Grille)
| *a | Hook |
|
Remove in this Direction |
Disengage the 4 claws and 2 guides as shown in the illustration.
Disengage the hook to remove the front bumper hole cover LH.
52128B
23.REMOVE FRONT BUMPER HOLE COVER LH (for Mesh Type Radiator Grille)
| *a | Hook |
|
Remove in this Direction |
Disengage the 5 claws as shown in the illustration.
Disengage the hook to remove the front bumper hole cover LH.
52127D
24.REMOVE FRONT BUMPER HOLE COVER RH (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
53395E
25.REMOVE HOOD TO FRONT END PANEL SEAL
Disengage the 6 clips.
|
Double-sided Tape |
Separate the double-sided tape and disengage the guide to remove the hood to front end panel seal.
75310A
26.REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY
Remove the screw.
Disengage the 4 claws and guide to remove the radiator grille emblem assembly.
27.REMOVE FRONT BUMPER UPPER RETAINER
Use the same procedure for the RH side and LH side.
Remove the screw.
Disengage the 2 guides to remove the front bumper upper retainer.
52111F
28.REMOVE FRONT CENTER BUMPER BAR (for Bar Type Radiator Grille)
| *a | Clip |
| *b | Screw |
Remove the 2 clips.
Remove the 4 screws and front center bumper bar.
53101
29.REMOVE RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)
Remove the 2 screws.
Disengage the 10 claws and guide to remove the radiator grille sub-assembly.
53101
30.REMOVE RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)
Remove the 2 clips.
Remove the 10 screws.
Disengage the 8 claws to remove the radiator grille sub-assembly.
81220
31.REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210A
32.REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure as for the LH side.
52713A
33.REMOVE FRONT BUMPER SIDE MOULDING LH (for Bar Type Radiator Grille)
Remove the 5 screws.
Disengage the 3 claws and 2 guides to remove the front bumper side moulding LH.
52712
34.REMOVE FRONT BUMPER SIDE MOULDING RH (for Bar Type Radiator Grille)
Use the same procedure as for the LH side.
81482C
35.REMOVE FOG LIGHT COVER LH (for Mesh Type Radiator Grille)
Remove the 4 clips.
Remove the clip.
Disengage the 6 claws to remove the fog light cover LH.
81481E
36.REMOVE FOG LIGHT COVER RH (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
53124D
37.REMOVE LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)
Remove the screw.
Disengage the 8 claws and guide to remove the lower radiator grille moulding LH.
53123C
38.REMOVE LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
52534
39.REMOVE FRONT NO. 2 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)
|
Double-sided Tape |
Disengage the claw and separate the double-sided tape to remove the front No. 2 bumper retainer bracket.
52533
40.REMOVE FRONT NO. 1 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
53122G
41.REMOVE LOWER CENTER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)
Remove the screw.
Disengage the 4 claws and guide to remove the lower center radiator grille moulding.
53102A
42.REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)
Remove the 4 screws.
Disengage the 17 claws to remove the lower radiator grille sub-assembly.
53102A
43.REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)
Remove the 4 screws.
Disengage the 24 claws and 6 guides to remove the lower radiator grille sub-assembly.
52713A
44.REMOVE FRONT BUMPER SIDE MOULDING LH (for Mesh Type Radiator Grille)
Remove the 2 clips.
Disengage the 2 claws and 2 guides to remove the front bumper side moulding LH.
52712
45.REMOVE FRONT BUMPER SIDE MOULDING RH (for Mesh Type Radiator Grille)
Use the same procedure as for the LH side.
47749F
46.REMOVE PIN HOLD CLIP
|
Remove in this Direction |
Disengage the 4 claws to remove the 2 pin hold clips as shown in the illustration.
Use the same procedure for the RH side and LH side.
53879H
47.REMOVE FRONT FENDER LINER RETAINER
|
Remove in this Direction |
Remove the 2 front fender liner retainers as shown in the illustration.
Use the same procedure for the RH side and LH side.
52611
48.REMOVE FRONT BUMPER ENERGY ABSORBER
|
Remove in this Direction |
Disengage the 4 guides to remove the front bumper energy absorber as shown in the illustration.
52131A
49.REMOVE FRONT BUMPER REINFORCEMENT
Remove the headlight assembly LH.
for LED Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
for Bulb Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the headlight assembly RH.
Use the same procedure as for the LH side.
Disengage the 4 clamps.
Remove the 6 bolts and front bumper reinforcement.
52536
50.REMOVE FRONT BUMPER SIDE RETAINER LH
Remove the bolt.
|
Remove in this Direction |
Disengage the 2 clips to remove the front bumper side retainer LH as shown in the illustration.
52535
51.REMOVE FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.