Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _078700 TELEMATICS _0387130 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B153711  Telephone Sub Antenna Circuit Short to Ground  B153713  Telephone Sub Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B153711 Telephone Sub Antenna Circuit Short to Ground Navigation antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telematics transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)


B153713 Telephone Sub Antenna Circuit Open Navigation antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telematics transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly (for Type A)

·

Antenna cord sub-assembly (for Type B)



WIRING DIAGRAM

E338342E67
1.146,0.427 1.865,0.646 0.719,0.219 10 false 4 0.167,1.063 0.813,1.25 0.646,0.188 10 false F 6.146,1.219 6.885,1.604 0.74,0.385 10 false Telematics Transceiver 2.094,0.688 2.438,0.865 0.344,0.177 10 false *2 3.417,0.344 3.625,0.51 0.208,0.167 10 false 3 3.833,0.354 4.021,0.531 0.188,0.177 10 false 3 3.417,0.552 3.625,0.719 0.208,0.167 10 false E 3.823,0.552 4.219,0.719 0.396,0.167 10 false D 4.99,0.677 5.333,0.854 0.344,0.177 10 false *1 5.896,0.396 6.104,0.594 0.208,0.198 10 false 1 5.969,1.063 6.365,1.229 0.396,0.167 10 false A 1.26,2.667 5.958,2.927 4.698,0.26 10 false *1: Antenna Cord Sub-assembly (for Type B) 0.156,1.25 1.385,1.688 1.229,0.438 10 false Navigation Antenna Assembly 1.26,3.115 5.958,3.375 4.698,0.26 10 false *2: Antenna Cord Sub-assembly (for Type A)

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the Techstream on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NAVIGATION ANTENNA ASSEMBLY
2.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type A)
a.
E334514C25
0.656,1.031 1.031,1.281 0.375,0.25 2.177,0.833 2.375,0.438 false 0.792,1.073 1.104,1.271 0.313,0.198 10 false F 2.396,0.281 2.708,0.479 0.313,0.198 10 false 4a 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the F antenna cord sub-assembly (for Type A) connector.


b.
E452653C01
1.563,0.292 1.865,0.552 0.302,0.26 2.083,1.375 2.438,1.656 false 1.677,0.333 1.833,0.531 0.156,0.198 10 false E 2.531,1.563 2.844,1.76 0.313,0.198 10 false 3a 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type A))


Disconnect the E antenna cord sub-assembly (for Type A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-4 - E-3 Always Below 1 Ω
F-4 or E-3 - Body ground Always 10 kΩ or higher
F-4a - E-3a Always Below 1 Ω
F-4a or E-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type A)

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Type B)
a.
E215788C94
1.583,0.375 1.906,0.604 0.323,0.229 1.083,1.677 1.49,1.365 false 0.865,1.635 1.177,1.833 0.313,0.198 10 false 3a 0.177,0.177 0.49,0.375 0.313,0.198 10 false *a 1.698,0.406 1.854,0.604 0.156,0.198 10 false D
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the D antenna cord sub-assembly (for Type B) connector.


b.
E418543C21
1.448,0.167 1.865,0.417 0.417,0.25 1.115,1.771 1.448,1.417 false 1.615,0.229 1.771,0.427 0.156,0.198 10 false A 0.906,1.74 1.24,1.938 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected (Antenna Cord Sub-assembly (for Type B))


Disconnect the A antenna cord sub-assembly (for Type B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-3 - A-1 Always Below 1 Ω
D-3 or A-1 - Body ground Always 10 kΩ or higher
D-3a - A-1a Always Below 1 Ω
D-3a or A-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Type B)

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT