Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › CAMSHAFT › from 2021.02
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324463 CAMSHAFT A

A25A-FXS ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23100X 1.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 88710E 2.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

for LHD:

i.
A447262

Disengage the 2 clamps and disconnect the air conditioning tube and accessory assembly.



b.

for RHD:

i.
A447263

Disengage the 2 clamps and disconnect the air conditioning tube and accessory assembly.



Hide 82121 3.DISCONNECT ENGINE WIRE

a.
A445983

Disconnect the 6 connectors.


b.

Disengage the 3 clamps and disconnect the engine wire.


Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 7.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 135A0A 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

Hide 13090D 9.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 10.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 12.REMOVE SPARK PLUG TUBE GASKET

Hide 23477 13.REMOVE FUEL PUMP LIFTER GUIDE

Hide 14.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A445984C01
2.427,3.938 2.656,4.229 2.656,4.229 2.802,4.229 true 2.083,4.313 2.24,4.313 2.24,4.313 2.344,3.865 true 1.406,1.521 1.271,1.521 1.271,1.521 1.146,1.156 true 0.813,1.552 0.813,1.354 0.813,1.354 1.083,1.042 true 0.792,0.583 0.979,0.583 0.979,0.583 1.135,0.792 true 2.698,0.781 2.875,0.438 2.875,0.438 3.052,0.438 true 2.698,0.885 2.927,0.771 2.927,0.771 3.135,0.771 true 3.01,1.479 2.833,1.479 2.833,1.479 2.677,1.031 true 0.729,1.583 0.938,1.771 0.208,0.188 10 true *a 1.896,4.229 2.094,4.417 0.198,0.188 10 true *b 2.823,4.146 3.021,4.344 0.198,0.198 10 true *c 1.438,1.438 1.635,1.625 0.198,0.188 10 true *b 3.156,0.688 3.354,0.885 0.198,0.198 10 true *b 3.073,0.344 3.281,0.542 0.208,0.198 10 true *b 0.604,0.5 0.792,0.688 0.188,0.188 10 true *b 3.042,1.396 3.25,1.583 0.208,0.188 10 true *a
*a Paint Mark
*b Timing Mark
*c "0" Timing Mark


Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley assembly with the "0" timing mark on the No. 2 timing gear cover assembly.


b.

Check that the timing marks are positioned as shown in the illustration.

HINT:

If the timing marks are not positioned as shown in the illustration, turn the crankshaft clockwise and then align them again.



c.

Place paint marks on the chain sub-assembly at points aligned with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.


Hide 16.REMOVE CAMSHAFT

a.
A445985C01
2.49,1.938 2.708,2.135 0.219,0.198 10 true *a
*a Approximately 15°


Rotate the crankshaft approximately 15° clockwise.


b.
A445986C01
2.469,1.927 2.677,2.135 0.208,0.208 10 true *a
*a Approximately 15°


Rotate the crankshaft approximately 15° counterclockwise.


c.
A445987C01
0.875,1.771 1.167,1.771 true 1.198,3.25 1.375,3.25 1.375,3.25 1.594,3.573 true 1.604,3.74 1.75,3.875 1.75,3.875 1.75,4.052 true 0.667,1.677 0.875,1.885 0.208,0.208 10 true *a 0.99,3.156 1.188,3.354 0.198,0.198 10 true *b 1.656,4.063 1.865,4.25 0.208,0.188 10 true *c
*a Pin
*b Pin Hole (No. 1 Chain Tensioner Assembly Side)
*c Pin Hole (Chain Tensioner Slipper Side)


Align the pin hole of the No. 1 chain tensioner assembly with the pin hole of the chain tensioner slipper, and then insert the pin.


d.

Type A:

i.
A445988C01
2.938,0.042 3.167,0.229 0.229,0.188 10 false *a
*a Hold


Using the hexagonal portion of the No. 2 camshaft, secure the No. 2 camshaft.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



ii.

Using a 5 mm hexagon wrench, remove the 2 bolts from the camshaft timing exhaust gear assembly.



e.

Type B:

i.
A473301C01
2.938,0.042 3.167,0.229 0.229,0.188 10 false *a
*a Hold


Using the hexagonal portion of the No. 2 camshaft, secure the No. 2 camshaft.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



ii.

Using a 5 mm hexagon wrench, remove the 2 bolts from the camshaft timing exhaust gear assembly.



f.
A445989C01
2.229,0.073 2.458,0.25 0.229,0.177 10 true *a
*a Hold
V113147

Turn


Using the hexagonal portion of the camshaft, secure the camshaft.

NOTICE:
·

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.

·

Do not disassemble the camshaft timing gear assembly.




g.

Using a 10 mm bi-hexagon socket wrench, remove the bolt from the camshaft timing gear assembly.


h.

Using the hexagonal portion of the No. 2 camshaft, loosen and hold the chain sub-assembly while moving the No. 2 camshaft in the direction shown in the illustration.

A445990C01
5.406,0.063 5.635,0.281 0.229,0.219 10 false *a
*a Hold - -
V100135

Turn - -



i.

Move the camshaft timing gear assembly together with the camshaft timing exhaust gear assembly and chain sub-assembly toward the No. 2 timing gear cover assembly as shown in the illustration.

A445991C01
2.479,0.813 2.833,0.385 2.833,0.385 3.021,0.385 true 2.042,1.438 2.365,1.438 true 2.552,2.146 2.833,2.542 2.833,2.542 3.031,2.542 true 3.063,0.323 3.24,0.5 0.177,0.177 10 false *1 3.073,2.469 3.271,2.646 0.198,0.177 10 false *2 1.844,1.354 2.052,1.552 0.208,0.198 10 true *3
*1 Camshaft Timing Gear Assembly *2 Camshaft Timing Exhaust Gear Assembly
*3 Chain Sub-assembly - -
V113147

Remove in this Direction - -



j.

Remove the camshaft timing exhaust gear assembly from the chain sub-assembly.


k.

Remove the camshaft timing gear assembly from the chain sub-assembly.


l.
A445992

Secure the chain sub-assembly to the vehicle using rope, etc.

NOTICE:

Do not drop the chain sub-assembly into the timing chain cover assembly.



m.
A445993N01
3,1.552 3.125,1.729 0.125,0.177 10 true 2 0.656,1.542 0.781,1.719 0.125,0.177 10 true 1 1.354,0.406 1.479,0.583 0.125,0.177 10 true 3 1.24,1.542 1.365,1.719 0.125,0.177 10 true 4 2.5,0.427 2.625,0.604 0.125,0.177 10 true 5 2.396,1.531 2.521,1.708 0.125,0.177 10 true 6 1.927,0.427 2.052,0.604 0.125,0.177 10 true 7 1.823,1.542 1.948,1.719 0.125,0.177 10 true 8

Uniformly loosen and remove the 8 bolts in the order shown in the illustration.


n.
A445994C01
1.125,0.885 1.302,0.885 true 0.26,0.802 0.448,0.802 true 1.375,1.344 1.375,1.177 1.375,1.177 1.604,1.052 true 2.552,0.802 2.729,0.802 true 1.948,1.344 1.948,1.177 1.948,1.177 2.177,1.052 true 3.198,0.063 3.333,0.24 0.135,0.177 10 false 1 3.177,1.417 3.313,1.594 0.135,0.177 10 true 2 2.865,0.052 3,0.229 0.135,0.177 10 false 3 2.948,1.958 3.083,2.135 0.135,0.177 10 true 4 2.385,1.396 2.521,1.573 0.135,0.177 10 true 5 0.802,0.021 0.938,0.198 0.135,0.177 10 true 6 0.729,1.969 0.865,2.146 0.135,0.177 10 true 7 0.885,0.813 1.021,0.99 0.135,0.177 10 true 8 2.385,0.073 2.521,0.25 0.135,0.177 10 false 9 2.365,1.99 2.563,2.156 0.198,0.167 10 true 10 1.219,0.052 1.417,0.219 0.198,0.167 10 true 11 1.24,1.979 1.438,2.146 0.198,0.167 10 true 12 1.771,0.083 1.969,0.25 0.198,0.167 10 false 13 1.771,1.99 1.969,2.156 0.198,0.167 10 true 14 0.052,0.729 0.26,0.917 0.208,0.188 10 true *1 1.323,0.802 1.521,0.969 0.198,0.167 10 true *2 1.281,1.365 1.479,1.552 0.198,0.188 10 true *3 2.354,0.74 2.542,0.917 0.188,0.177 10 true *4 1.875,1.354 2.073,1.542 0.198,0.188 10 true *3
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Uniformly loosen and remove the 14 bolts in the order shown in the illustration.

NOTICE:

Uniformly loosen the bolts while holding the camshaft horizontally.



o.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



p.
A445995

Remove the camshaft from the camshaft housing sub-assembly.


q.
A445996

Remove the No. 2 camshaft from the camshaft housing sub-assembly.