Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2021.02
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324466 REAR CRANKSHAFT OIL SEAL A

A25A-FXS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for Nickel Metal Hydride Battery
(Click here)for Lithium-ion Battery
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

·

Replacement of front bumper assembly


·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic View Monitor System (Click here)for Initialization
(Click here)for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A407561N02
1.521,0.896 1.167,0.479 1.167,0.479 1.927,0.656 true 0.74,0.354 1.115,0.552 0.375,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A406362

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.


Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A407561N03
1.521,0.896 1.167,0.479 1.167,0.479 1.927,0.656 true 0.74,0.354 1.115,0.552 0.375,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A406363

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 19315 4.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Type A:

i.
A406346

Remove the No. 1 crankshaft position sensor plate.



b.

Type B:

i.
A471040

Remove the No. 1 crankshaft position sensor plate.



Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A400434C01
2.896,1.531 2.896,1.188 2.896,1.188 3.125,0.917 false 1.813,1.854 1.552,1.854 1.552,1.854 1.26,1.365 true 1.875,1.75 2.188,1.948 0.313,0.198 10 true *a 2.813,1.573 3.125,1.771 0.313,0.198 10 true *b
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.