Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2021.02
RM33C0E _51 Engine / Hybrid System _065421 A25A-FXS FUEL _0319768 FUEL INJECTOR(for Port Injection) A

A25A-FXS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for Nickel Metal Hydride Battery
(Click here)for Lithium-ion Battery
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module
·

Replacement of port fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25620 6.REMOVE EGR VALVE ASSEMBLY

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 23910A 8.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A403914

Remove the fuel pipe clamp from the fuel tube connector.


b.
A403915

Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 9.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A405311

Disconnect the ignition coil connector.


b.

for EGR Valve Bracket Connection Type:

i.
A405312

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



c.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A463922C01
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


ii.

Using an 8 mm socket wrench, remove the bolt.



d.
A406621

Loosen the 2 bolts of the fuel pump assembly.


e.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 23800 10.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.
A403916

Disconnect the No. 5 engine wire connector.


b.
A405310

Remove the 2 bolts and fuel delivery pipe with sensor assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.



Hide 23807V 11.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A403917

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23291 12.REMOVE INJECTOR VIBRATION INSULATOR

a.
A403918

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 13.REMOVE NO. 5 ENGINE WIRE

a.
A401651

Disconnect the 4 port fuel injector assembly connectors and fuel pressure sensor connector.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


Hide 23250F 14.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A401652

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


b.
A401653

Remove the O-ring from each port fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.